A.Configure the switch to be in VTP client mode.
B.Configure the switch to be in VTP domaint mode.
C.Configure the switch to be in VTP transparent mode.
D.Configure the switch to be in VTPv2
您可能感興趣的試卷
你可能感興趣的試題
A.show interfaces interface
B.show interfaces interface trunk
C.show interfaces interface switchport
D.show ip interface brief
E.show interfaces vlan
A.Telnet to WANRouter and execute the command show interfaces S0/0
B.Telnet to WANRouter and execute the command show processes S0/0
C.Telnet to WANRouter and execute the command show running-configuration
D.Telnet to WANRouter and execute the command show controller S0/0
E.Physically examine the cable between WANRouter S0/0 and the DCE
F.Establish a console session on WANRouter and execute the command show interfaces S0/0
Refer to the topology shown in the exhibit. Which ports will be STP designated ports if all the links are operating at the same bandwidth? ()
A.Switch A - Fa0/0
B.Switch A - Fa0/1
C.Switch B - Fa0/0
D.Switch B - Fa0/1
E.Switch C - Fa0/0
F.Switch C - Fa0/1
A.to make VTP easier to implement
B.to isolate broadcast traffic
C.to increase the size of the collision domain
D.to allow more devices to connect to the network
E.to logically group hosts according to function
F.to increase network security
A.proxy
B.dual-stack
C.tunneling
D.dot1q
最新試題
請參見圖示。當計算機A 向計算機D 發送幀時,哪些計算機會接收該幀?()
請參見圖示。網絡中的所有設備均使用默認配置。此拓?fù)渲行枰嗌賯€(gè)邏輯地址范圍?()
請參見圖示。某用戶想要查看當前的配置。圖中所示為ipconfig/all 命令的輸出。從此輸出可以得到哪三項結論?()
請參見圖示。主機X 和主機Y 與本地網絡的通信受到限制。此問題的原因是什么?()
請參見圖示。一臺路由器(其路由表如圖所示)收到發往192.168.1.4的數據包。路由器將如何處理該數據包?()
請參見圖示。RouterB 已經過正確配置。RouterA 的以太網接口Fa0/0已使用如圖所示的命令進行配置。但是,從RouterA 的Fa0/0接口無法成功ping 通RouterB 的Fa0/0接口。應在RouterA 上采取什么措施來解決此問題?()
請參見圖示。電纜1和電纜2分別按照特定的物理層要求接線。哪三個網段使用電纜2?()
以下哪兩種介質可提供高達1Gb/s 的帶寬?()
請參見圖示。網絡中的主機A 正在向主機B 發送數據段。有關所交換的數據段的流量控制如圖所示。下列關于此通信的陳述,哪兩項是正確的?()
何時必須使用clock rate 命令配置路由器串行接口?()