A.user EXEC mode
B.global configuration mode
C.privileged EXEC mode
D.auxiliary setup mode
您可能感興趣的試卷
你可能感興趣的試題
A.Router(config)#router ospf 1
B.Router(config)#router ospf 0
C.Router(config)#router ospf area 0
D.Router(config-router)#network 192.168.16.0 0.0.0.255 area 0
E.Router(config-router)#network 192.168.16.0 0.0.0.255 0
F.Router(config-router)#network 192.168.16.0 255.255.255.0 area 0
Refer to the exhibit.S0/0 on R1 is configured as a multipoint interface to communicate with R2 and R3 in the hub-and-spoke Frame Relay topology. While testing this configuration, a technician notes that pings are successfully from hosts on the 172.16.1.0/24 network to hosts on both the 172.16.2.0/25 and 172.16.0.2.128/25 networks. However, pings between hosts on the 172.16.2.0/25 and 172.16.2.128/25 network are not successful. What could explain this connectivity problem?()
A.The ip subnet-zero command has been issued on the R1 router.
B.The RIPv2 dynamic routing protocol cannot be used across a Frame Relay network.
C.Split horizon is preventing R2 from learning about the R3 networks and R3 from learning about R2 networks.
D.The 172.16.2.0/25 and 172.16.2.128/25 networks are overlapping networks that can be seen by R1,but not between R2 and R3.
E.The 172.16.3.0/29 network used on the Frame Relay links is creating a discontiguous network between the R2 and R3 router subnetworks.
A.when a packet is received from an 802.1Q trunk,the vlan id can be determined from the source MAC address table
B.unkown unicast frames are retransmitted only to the ports that belong to the same vlan
C.ports between switches should be configured in access mode so that vlans can span across the ports
D.broadcast and multicast frames are retransmitted to ports that are configured on different vlan.
A.to provide routing to a local web server
B.to provide routing from an ISP to a stub network
C.to provide routing that will override the configured dynamic routing protocol
D.to provide routing to a destination that is not specified in the routing table and which is outside the local network
A.RIP requires less time to converge
B.RIP uses less bandwidth
C.RIP is less complex to configure
D.RIP demands fewer router resources
E.RIP has a more accurate metric
最新試題
請參見圖示。對于從主機A 向Web 服務器發出的網頁請求,正確的目的套接字數字是什么?()
請參見圖示。RouterB 已經過正確配置。RouterA 的以太網接口Fa0/0已使用如圖所示的命令進行配置。但是,從RouterA 的Fa0/0接口無法成功ping 通RouterB 的Fa0/0接口。應在RouterA 上采取什么措施來解決此問題?()
請參見圖示。主機A 嘗試與主機C 建立TCP/IP 會話。在嘗試期間,路由器Y 的FastEthernet 接口fa0/1捕獲到一個幀。捕獲的幀中包含源IP 地址為172.16.1.5而目的IP 地址為172.16.7.24的數據包。捕獲該幀時,它的源MAC 地址是什么?()
請參見圖示。主機B 嘗試與主機C 建立TCP/IP 會話。在嘗試期間,San Francisco 器由器的FastEthernet 接口fa0/1捕獲到一個幀。捕獲的幀中包含源IP 地址為10.10.1.2而目的IP 地址為10.31.1.20的數據包。捕獲該幀時,它的目的MAC 地址是什么?()
請參見圖示。網絡中的主機A 正在向主機B 發送數據段。有關所交換的數據段的流量控制如圖所示。下列關于此通信的陳述,哪兩項是正確的?()
請參見圖示。網絡技術人員使用圖中所示的連接將主機A 連接到路由器以創建初始配置。下列有關此連接的陳述中哪一項正確?()
要將數據包發送到遠程網絡,應使用哪種設備?()
在配置路由器時,網絡技術人員想要命名路由器。輸入hostname 命令后,技術人員會看到下列哪一項提示?()
請參見圖示。主機A 正在訪問多臺服務器。結合使用什么端口號和地址即可唯一識別特定服務器上運行的特定進程?()
請參見圖示。下列哪組設備僅包含中間設備?()