單項選擇題A network administrator needs to force a high-performance switch that is located in the MDF to become the root bridge for a redundant path switched network. What can be done to ensure that this switch assumes the role as root bridge?()

A.Establish a direct link from the switch to all other switches in the network.
B.Assign the switch a higher MAC address than the other switches in the network have.
C.Configure the switch so that it has a lower priority than other switches in the network.
D.Configure the switch for full-duplex operation and configure the other switches for half-duplex operation.
E.Connect the switch directly to the MDF router, which will force the switch to assume the role of root bridge.


您可能感興趣的試卷

你可能感興趣的試題

1.單項選擇題What is the purpose of the command shown below? vtp password Fl0r1da()。

A.It is used to validate the sources of VTP advertisements sent between switches.
B.It is used to access the VTP server to make changes to the VTP configuration.
C.It allows two VTP servers to exist in the same domain, each configured with different passwords.
D.It is the password required when promoting a switch from VTP client mode to VTP server mode.
E.It is used to prevent a switch newly added to the network from sending incorrect VLAN information to the other switches in the domain.

2.多項選擇題What are two reasons a network administrator would use CDP? (Choose two.)()

A.to verify the type of cable interconnecting two devices
B.to determine the status of network services on a remote device
C.to obtain VLAN information from directly connected switches
D.to verify Layer 2 connectivity between two devices when Layer 3 fails
E.to obtain the IP address of a connected device in order to telnet to the device
F.to determine the status of the routing protocols between directly connected routers

3.單項選擇題Why will a switch never learn a broadcast address?()

A.Broadcasts only use network layer addressing.
B.A broadcast frame is never forwarded by a switch.
C.A broadcast address will never be the source address of a frame.
D.Broadcast addresses use an incorrect format for the switching table.
E.Broadcast frames are never sent to switches.

4.單項選擇題Which additional configuration step is necessary in order to connect to an access point that has SSID broadcasting disabled?()

A.Set the SSID value in the client software to public.
B.Configure open authentication on the AP and the client.
C.Set the SSID value on the client to the SSID configured on the AP
D.Configure MAC address filtering to permit the client to connect to the AP

最新試題

Three switches are connected to one anther via trunk ports.Assuming the default switch configuration,which switch is elected as the root bridge for the spanning-tree instance of vlan 1?()

題型:單項選擇題

Which IPsec security protocol should be used when confidentiality is required?()

題型:單項選擇題

Which encapsulation type is a Frame Relay encapsulation type that is supported by Cisco routers?()

題型:單項選擇題

An administrator must assign static IP addresses to the servers in a network.For network 192.168.20.24/29, the router is assigned the first usable host address while the sales server is given the last usable host address. Which of the following should be entered into the IP propertied box for the sales server?()

題型:單項選擇題

While troubleshooting a network problem,a technician discovers that the current copy of the Cisco IOS is outdated and needs to be updated.Which of the following commands would the technician issue to replace the Cisco router IOS with the newer version?()

題型:單項選擇題

The network administrator cannot to switch 1 over a telnet session,although the hosts attached to switch 1 can ping the interface Fa0/0 of the router.Given the information in the graphic and assuming that the router and switch2 are configured properly,which of the following commands should be issued on switch 1 to correct this problem?()

題型:單項選擇題

At which layer of the OSI model is RSTP used to prevent loops?()

題型:單項選擇題

A router receives information about network 192.168.10.0/24 from multiple sources.What will the router consider the most reliable information about the path to that network?()

題型:單項選擇題

A network administrator is trying to add a new router into an established OSPF network.The networks attached to the new router do not appear in the routing tables of the other OSPF routers.Given the information in the partial configuration shown below,what configuration error is causing this problem?()Router(config)#router ospf 1Router(config-router)#network 10.0.0.0 255.0.0.0 area 0

題型:單項選擇題

An employee of ABC company has move to an office on a different floor. Although the administrator is able to telnet to all of the routers,the address of Switch F is needed in order to verify that the employee remains in the same VLAN.Which action could be used by the administrator to find the IP address of Switch F?()

題型:單項選擇題