A. The trunking configuration mode on Switch1 is set to Off.
B. The trunking configuration mode on the other end is set to On.
C. The trunking configuration mode on the other end is set to Desirable.
D. Cisco Discovery Protocol is not running on the other end.
E. There is a VTP domain name mismatch.
F. Switch1 does not support 802.1Q
您可能感興趣的試卷
你可能感興趣的試題
A.It allows the standby RP to take control of the device after a hardware or software fault on the active RP.
B.It is a Layer 3 function that works with SSO to minimize the amount of time a network is unavailable tousers following a switchover.
C.It is supported by the implementation of EIGRP， OSPF， RIPv2， and BGP protocols.
D.It synchronizes startup configuration， startup variables， and running configuration.
E.The main objective of NSF is to continue forwarding IP packets following a switchover.
F.Layer 2 802.1w or 802.1s must be used， as 802.1d cannot process the Layer 2 changes.
G.Routing protocol tuning parameters must be the same as the NSF parameters， or failover will beinconsistent.
A. The VSS switch must be the root bridge for all VLANs and is automatically designated
B. The VSS switch is defined in RFC 4318 as a managed object
C. The PAgP+ or LACP protocols are used to maintain the operational state of the VSS devices
D. A VSS interoperates with a virtual port channel
E. The 802.1Q or ISL protocols are used to maintain the operational state of the VSS devices
F. A VSS increases the size of the spanning-tree domain
A.telnet 11.1.1.4 /vrf-source red
B.telnet 11.1.1.4 source /vrf red
C.telnet 11.1.1.4 /source vrf red
D.telnet 11.1.1.4 /vrf red
E.telnet 11.1.1.4 vrf red
A.all routes in the routing table
B.only the IGP and BGP routes in the routing table
C.only the BGP routes in the routing table
D.only the IGP routes in the routing table
A.ip vrf CCIE
B.ipv6 vrf CCIE
C.vrf definition CCIE
D.ipv6 vrf definition CCIE
最新試題
In Layer 2 topologies， spanning-tree failures can cause loops in the network. These unblocked loops cancause network failures because of excessive traffic. Which two Catalyst 6500 features can be used to limitexcessive traffic during spanning-tree loop conditions？（）
What is the correct command to set the router ID for an OSPFv3 process？（）
Which command is used to enable SSM with the range 232.0.0.0 - 255.0.0.0？（）
How does an IPv6 router deal with a packet that is larger than the outgoing interface MTU？（）
Which of the following is true about the MPLS header and its EXP field size？（）
On the basis of the network provided in the exhibit， all routers are configured to run EIGRP on all links. If the link between PG-R1 and PG-R2 fails， what is the maximum number of queries PG-R3 will receive for 192.168.1.0/24， assuming that all the packets sent during convergence are transmitted once （there are no dropped or retransmitted packets）？（）
Which types of prefixes will a router running BGP most likely advertise to an IBGP peer， assuming it is notconfigured as a route reflector？（）
In PIM-SM what control plane signaling must a multicast source perform before it begins to send multicasttraffic to a group？（）
Which of these statements about penultimate hop popping are true？（）
Two routers configured to run BGP have been connected to a firewall， one on the inside interface and one on the outside interface. BGP has been configured so the two routers should peer， including the correctBGP session endpoint addresses and the correct BGP session hop-count limit EBGP multihop. What is agood first test to see if BGP will work across the firewall？（）