A. Cisco NX-OS Software does not support PIM dense mode.
B. The command ip multicast-routing must be enabled in Cisco NX-OS Software before any multicast configuration is possible on the switch.
C. PIM CLI configuration and verification commands are not available until you enable the PIM feature with the feature pim command.
D. Cisco NX-OS Software supports multicast routing per Layer 3 VRF instance.
E. The default PIM operational mode on the Cisco Nexus 7000 switch is SSM.
您可能感興趣的試卷
你可能感興趣的試題
A. The L2 multicast frames are encapsulated in an OTV packet using the configured control-group multicast address for transport
B. The L2 multicast frames are dropped because multicast cannot be carried across the overlay
C. The L2 multicast frames are encapsulated in an OTV packet using the configured data-group multicast address for transport
D. The L2 multicast frames are forwarded natively across the overlay based on their multicast IDs
A. 128
B. 32
C. 64
D. Dependent on the number of switch IDs in the topology
A. IGMP snooping is not active for VLAN 120 because the IGMP feature has not been enabled on the switch with the feature igmp command.
B. The IGMP snooping querier for VLAN 120 is not in a running state because the Loopback interface configured with 1.1.1.1/32 is currently in a down state.
C. IGMP snooping has been disabled on the VLAN 120 SVI.
D. IGMP snooping has been disabled for VLAN 120 in VLAN configuration mode.
E. IGMP snooping is not active for VLAN 120 because VLAN 120 does not exist in the VLAN database.
Nexus# sh ip igmp snooping vlan 120
IGMP Snooping information for vlan 120
IGMP snooping disabled
Optimised Multicast Flood （OMF） disabled
IGMP querier none
Switch-querier enabled， address 1.1.1.1， currently not running
IGMPv3 Explicit tracking enabled
IGMPv2 Fast leave disabled
IGMPv1/v2 Report suppression enabled
IGMPv3 Report suppression disabled
Link Local Groups suppression enabled
Router port detection using PIM Hellos， IGMP Queries
Number of router-ports： 0
Number of groups： 0
Active ports： Po100 Po111
Which statement best describes what is depicted in the show command output？（）
A. IGMP snooping is not active for VLAN 120 because the IGMP feature has not been enabled on the switch with the feature igmp command.
B. The IGMP snooping querier for VLAN 120 is not in a running state because the Loopback interface configured with 1.1.1.1/32 is currently in a down state.
C. IGMP snooping has been disabled on the VLAN 120 SVI.
D. IGMP snooping has been disabled for VLAN 120 in VLAN configuration mode.
E. IGMP snooping is not active for VLAN 120 because VLAN 120 does not exist in the VLAN database.
A. Synchronizes ARP entries between vPC peers every five minutes
B. Triggers a manual update of ARP entries from the primary peer to the secondary
C. Enables a bulk loading of ARP entries when a vPC peer is restored
D. Uses the peer-keepalive link to maintain ARP table consistency
最新試題
Given the following output： san-port-channel 12 is up Hardware is Fibre Channel Port WWN is 24：0c：00：0d：ec：d3：5c：00 Admin port mode is NP， trunk mode is on Port mode is NP Port vsan is 1 Speed is 8 Gbps Member[1] ： fc2/3 Member[2] ： fc2/4 What does "Speed is 8 Gbps" indicate？（）
What would be the cause for the following fault in UCS Manager？（） "ether VIF x / xxx down， reason： ENM source pinning failed"
In a Cisco Unified Computing System， where are SAN port channels connected to？（）
Which of the following are supported in Cisco Global Site Selector？ （）
Which is true when describing a connection replication in Cisco ACE？（）
When will an "all configuration" backup be imported into the Cisco UCS Manager？（）
Which statements are true regarding the Cisco UCS fabric failover feature？ （）
A Cisco Application Control Engine Appliance （ACE） non-admin context does not support "sticky" configuration. What is the reason for this issue？（）
Where are SAN Port Channel is created in UCS Manager？（）
What is the purpose of this command in a Cisco Application Control Engine？（） switch/Admin# show np 1 me-stats "-F0 v"