Nexus7000# config t
Nexus700（config）# interface ethernet 2/11
Nexus700（config-if）# switchport mode private-vlan host
Nexus700（config-if）# switchport private-vlan host-association 14 50
Nexus700（config-if）# exit
Nexus700（config）#
What will this command sequence achieve？（）
A. associate interface E2/11 to community VLANs 14 and 50
B. associate interface E2/11 to secondary VLANs 14 and 50
C. associate interface E2/11 to primary VLAN 50 and secondary VLAN 14
D. associate interface E2/11 to primary VLAN 14 and secondary VLAN 50
您可能感興趣的試卷
你可能感興趣的試題
A. Port priority value can be configured between 1 and 65535.
B. A higher port priority value means a higher priority of LACP.
C. Port priority can be configured so that specific links can be chosen as active links rather than the hot standby links within the port channel.
D. LACP uses the port priority with the port number to form the port identifier.
E. LACP Port priority default value should always be changed
A. Cisco AV-pair
B. TACACS+ or RADIUS ack frame role attribute
C. DH-CHAP challenge attribute
D. privilege level attribute
A. Graceful consistency check is enabled by default.
B. When graceful consistency check is enabled， only the links on the secondary peer device are suspended.
C. Graceful consistency check is disabled by default， so to enable this feature， use graceful consistency-check command under VPC domain configuration mode.
D. When graceful consistency check is enabled， only the inconsistent VLANs on the secondary peer device are suspended.
A. A single VACL can be shared across two or more VDCs.
B. Use of VACLs requires no special license to be installed.
C. VACLs make use of IP or MAC ACLs.
D. Only options drop and forward are permitted.
A. Adjacency Server is required when OTV is deployed with unicast-only transport.
B. Adjacency Server is required when OTV is deployed with multicast-enabled transport.
C. Each OTV device wishing to join a specific OTV logical overlay needs to first register with the Adjacency Server.
D. Each OTV device trying to join a specific OTV logical overlay needs to be configured as an Adjacency Server.
最新試題
Which three statements are possible causes for the "fltAdaptorHostIfLink-down" fault in UCS Manager？ （）
Given the following output： san-port-channel 12 is up Hardware is Fibre Channel Port WWN is 24：0c：00：0d：ec：d3：5c：00 Admin port mode is NP， trunk mode is on Port mode is NP Port vsan is 1 Speed is 8 Gbps Member[1] ： fc2/3 Member[2] ： fc2/4 What does "Speed is 8 Gbps" indicate？（）
Where are SAN Port Channel is created in UCS Manager？（）
Which statements are true regarding the Cisco UCS fabric failover feature？ （）
Your company wants Server 1/eth0 （vNIC 1） configured so that it always uses Fabric Interconnect A Port Channel 1 （Po1） when it communicates with anything outside of the Cisco UCS domain. However， if vNIC 1 fails over to Fabric Interconnect B using fabric failover， then vNIC 1 can any uplink port on Fabric Interconnect B. Which statements are true？ （）
What is the use of an "all configuration" backup in Cisco UCS？（）
Given a Cisco Unified Computing System， which is a valid port type in end-host mode？（）
Refer to the exhibit.Your company requires a Cisco UCS configuration that will， at a minimum， allow the configuration in the provided exhibit. Which Cisco UCS components will meet the requirement？（）
Which statement is true regarding Backup tasks in Cisco UCS？（）
Server load balancing （SLB） is the process of deciding to which server a load-balancing device should send a client request for service. Which predictors are supported on ACE in order to select the best server to fulfill a client request？ （）