A.End-to-end delay is the sum of propagation delays,processing delays,serialization delays,and queuing delays.
B.Coast-to-coast end-to-end delay over an optical link is about 20 ms.
C.Processing delay depends on various factors,which include CPU speed,CPU utilization,IP switching mode, and router architecture.
D.Propagation and serialization delays are related to the media.
E.Propagation delay is the time it takes to transmit a packet and is measured in bits-per-second (bps).
F.Serialization delay is the time it takes for a router to take the packet from an input interface and put it into the output queue of the output interface.
您可能感興趣的試卷
你可能感興趣的試題
A.class-based weighted fair queuing (CBWFQ)
B.low latency queuing (LLQ)
C.priority queuing (PQ) or custom queuing (CQ)
D.Real-Time Transport Protocol (RTP) header compression
E.TCP header compression
F.UDP header compression
Refer to the exhibit. Both routers have been configured as VoIP gateways. They must also support traditional telephony devices to connect to analog telephones. Which two configuration changes would correctly support the voice requirements?()
A.On each router, under the dial-peer voice 1 pots configuration, add the port fa0/0 command.
B.On each router, under the dial-peer voice 1 pots configuration, add the port 1/0/0 command.
C.On each router, configure dial-peer voice 1 as a voip connection and configure dial-peer voice 2 as a pots connection.
D.Under the dial-peer voice 1 pots configuration, change the destination pattern of 1111 to 2222 on the R1 router, and 2222 to 1111 on the R2 router.
E.Under the dial-peer voice 2 voip configuration, change the destination pattern of 1111 to 2222 on the R1 router, and 2222 to 1111 on the R2 router.
F.Under the dial-peer voice 2 voip configuration, change the destination target address of 10.2.2.2 to 10.1.1.1 on the R1 router, and the destination target address of 10.1.1.1 to 10.2.2.2 on the R2 router.
A.automated alternate routing (AAR)
B.Cisco CallManager Attendant Console
C.real-time protocol (RTP)
D.Survivable Remote Site Telephony (SRST)
A.Use the command ip nbar protocol-discovery to allow identification of stateful protocols. Use the command ip nbar port-map to attach the protocols to an interface.
B.Use the command match protocol rtp to allow identification of real-time audio and video traffic. Use thecommand ip nbar port-map to extend the NBAR functionality for well-known protocols to new port numbers.
C.Use the command match protocol to allow identification of stateful protocols. Use the command ip nbar port-map to attach the protocols to an interface.
D.Configure a traffic class. Configure a traffic policy. Attach the traffic policy to an interface.
E.Configure video streaming. Configure audio streaming. Attach the codec to an interface.
A.5
B.15
C.25
D.35
E.45
F.55
最新試題
For delay sensitive traffic, what are the three best ways that are used to prevent packet loss? ()
Which two VoIP capabilities are utilized when the CallManager and the gateway are configured for Survivable Remote Site Telephony?()
When Cisco SDM is used to generate QoS policy, various QoS classes will be created and assigned a percentage of the interface bandwidth. Which three statements indicate the default bandwidth values that are assigned by SDM for outgoing traffic on a WAN interface? ()
The Cisco SDM will create a QoS policy that provides services to two types of traffic. Which two statements indicate the default QoS parameters that are created by SDM?()
What are two ways to minimize the delay of VoIP packets that are traversing a network? ()
What are three factors used to determine the amount of bandwidth that is required for a single VoIP call? ()
Which three functions are associated with a Cisco Unified CallManager? ()
Which two commands should be entered on a WLAN controller to remove any residual configuration?()
What is an advantage of the IntServ QoS model?()
Which two functions can be provided by an Integrated Services Router (ISR) in a VoIP network?()