單項選擇題The Frame Relay network in the diagram is not functioning properly. What is the cause of the problem?()

A. The Gallant router has the wrong LMI type configured
B. Inverse ARP is providing the wrong PVC information to the Gallant router
C. The S3 interface of the Steele router has been configured with the frame-relay encapsulation ietf command
D. The frame-relay map statement in the Attalla router for the PVC to Steele is not correct
E. The IP address on the serial interface of the Attalla router is configured incorrectly


您可能感興趣的試卷

你可能感興趣的試題

1.單項選擇題A default Frame Relay WAN is classified as what type of physical network?()

A. point-to-point
B. broadcast multi-access
C. nonbroadcast multi-access
D. nonbroadcast multipoint
E. broadcast point-to-multipoint

2.單項選擇題The following configuration line was added to router R1 Access-list 101 permit ip 10.25.30.0 0.0.0.255 any What is the effect of this access list configuration?()

A. permit all packets matching the first three octets of the source address to all destinations
B. permit all packet matching the last octet of the destination address and accept all source addresses
C. permit all packet matching the host bits in the source address to all destinations
D. permit all packet from the third subnet of the network address to all destinations

3.單項選擇題The following access list below was applied outbound on the E0 interface connected to the 192.169.1.8/29 LAN: access-list 135 deny tcp 192.169.1.8 0.0.0.7 eq 20 any access-list 135 deny tcp 192.169.1.8 0.0.0.7 eq 21 any How will the above access lists affect traffic? ()

A. FTP traffic from 192.169.1.22 will be denied
B. No traffic, except for FTP traffic will be allowed to exit E0
C. FTP traffic from 192.169.1.9 to any host will be denied
D. All traffic exiting E0 will be denied
E. All FTP traffic to network 192.169.1.9/29 will be denied

5.單項選擇題A network administrator wants to add a line to an access list that will block only Telnet access by the hosts on subnet 192.168.1.128/28 to the server at 192.168.1.5. What command should be issued to accomplish this task?()

A. access-list 101 deny tcp 192.168.1.128 0.0.0.15 192.168.1.5 0.0.0.0 eq 23 access-list 101 permit ip any any
B. access-list 101 deny tcp 192.168.1.128 0.0.0.240 192.168.1.5 0.0.0.0 eq 23 access-list 101 permit ip any any
C. access-list 1 deny tcp 192.168.1.128 0.0.0.255 192.168.1.5 0.0.0.0 eq 21 access-list 1 permit ip any any
D. access-list 1 deny tcp 192.168.1.128 0.0.0.15 host 192.168.1.5 eq 23 access-list 1 permit ip any any

最新試題

Which protocol reduces administrative overhead in a switched network by allowing the configuration of a new VLAN to be distributed to all the switches in a domain?()

題型:單項選擇題

At which layer of the OSI model is RSTP used to prevent loops?()

題型:單項選擇題

Which Cisco IOS diagnostics command can disrupt the operation of a router under high-load conditions?()

題型:單項選擇題

Which cisco ios command can help to determine the timing of various debug events,relative to each other,when you are debugging a complicated router issue?()

題型:單項選擇題

When you are troubleshooting an ACL issue on a router,which command can help you to verify which interfaces are affected by the ACL?()

題型:單項選擇題

You have been asked to come up with a subnet mask that will allow all three web servers to be on the same network while providing the max number of subnets.Which network address and subnet mask meet this requirement?()

題型:單項選擇題

Which statement describes the rule of split horizon?()

題型:單項選擇題

An employee of ABC company has move to an office on a different floor. Although the administrator is able to telnet to all of the routers,the address of Switch F is needed in order to verify that the employee remains in the same VLAN.Which action could be used by the administrator to find the IP address of Switch F?()

題型:單項選擇題

At which layer of the OSI model dose PPP perform?()

題型:單項選擇題

A network administrator is trying to add a new router into an established OSPF network.The networks attached to the new router do not appear in the routing tables of the other OSPF routers.Given the information in the partial configuration shown below,what configuration error is causing this problem?()Router(config)#router ospf 1Router(config-router)#network 10.0.0.0 255.0.0.0 area 0

題型:單項選擇題