A. The new IOS image is too large for the router flash memory.
B. The TFTP server is unreachable from the router.
C. The new IOS image is not correct for this router platform.
D. The IOS image on the TFTP server is corrupt.
E. There is not enough disk space on the TFTP server for the IOS image.
您可能感興趣的試卷
你可能感興趣的試題
This graphic shows the results of an attempt to open a Telnet connection to router ACCESS1 from router Remote27. Which of the following command sequences will correct this problem? （）
A. ACCESS1(config)# line console 0 ACCESS1(config-line)# password cisco
B. Remote27(config)# line console 0 Remote27(config-line)# login Remote27(config-line)# password cisco
C. ACCESS1(config)# line vty 0 4 ACCESS1(config-line)# login ACCESS1(config-line)# password cisco
D. Remote27(config)# line vty 0 4 Remote27(config-line)# login Remote27(config-line)# password cisco
E. ACCESS1(config)# enable password cisco
F. Remote27(config)# enable password cisco
A network administrator is troubleshooting the OSPF configuration of routers R1 and R2. The routers cannot establish an adjacency relationship on their common Ethernet link. The graphic shows the output of the show ip ospf interface e0 command for routers R1 and R2. Based on the information in the graphic, what is the cause of this problem?（）
A. The OSPF area is not configured properly.
B. The priority on R1 should be set higher.
C. The cost on R1 should be set higher.
D. The hello and dead timers are not configured properly.
E. A backup designated router needs to be added to the network.
F. The OSPF process ID numbers must match.
A. A remote physical layer problem exists.
B. The host NIC is not functioning.
C. TCP/IP has not been correctly installed on the host.
D. A local physical layer problem exists.
A. 24
B. 4
C. 3
D. 16
A. The Gallant router has the wrong LMI type configured
B. Inverse ARP is providing the wrong PVC information to the Gallant router
C. The S3 interface of the Steele router has been configured with the frame-relay encapsulation ietf command
D. The frame-relay map statement in the Attalla router for the PVC to Steele is not correct
E. The IP address on the serial interface of the Attalla router is configured incorrectly
最新試題
An employee of ABC company has move to an office on a different floor. Although the administrator is able to telnet to all of the routers,the address of Switch F is needed in order to verify that the employee remains in the same VLAN.Which action could be used by the administrator to find the IP address of Switch F?（）
A network administrator needs to configure a serial link between the main office and a remote location.The router at the remote office is a non-cisco router. How should the network administrator configure the serial interface of the main office router to make the connection?（）
Which pairing reflects a correct protocol-and-metric relationship?（）
An administrator must assign static IP addresses to the servers in a network.For network 192.168.20.24/29, the router is assigned the first usable host address while the sales server is given the last usable host address. Which of the following should be entered into the IP propertied box for the sales server?（）
When you are troubleshooting an ACL issue on a router,which command can help you to verify which interfaces are affected by the ACL?（）
Which address is the IPV6 all-RIP-routers muticast group address that is used by RIPng as the destaion address?（）
At which layer of the OSI model is RSTP used to prevent loops?（）
Three switches are connected to one anther via trunk ports.Assuming the default switch configuration,which switch is elected as the root bridge for the spanning-tree instance of vlan 1?（）
Which command encrypts all plaintext passwords?（）
A network administrator is trying to add a new router into an established OSPF network.The networks attached to the new router do not appear in the routing tables of the other OSPF routers.Given the information in the partial configuration shown below,what configuration error is causing this problem?（）Router(config)#router ospf 1Router(config-router)#network 10.0.0.0 255.0.0.0 area 0