A. Only router can split boundaries(horizons)between concentric networks.
B. All distance vector protocols require fall routes that may cause momentary loops as the topology changes.
C. Networks can only remain fully converged if all information about routes is sent out all active interfaces.
D. Information about a route should not be sent back in the direction from which the original update came.
E. Each AS must keep routing tables converged to prevent dead routes from being advertised across the AS boundary.
您可能感興趣的試卷
你可能感興趣的試題
A. Router#copy tftp flash
B. Router(config)#restore flash
C. Router(config)#repair flash
D. Router#copy flash run
E. Router>copy start flash
F. Router#copy start flash
A. 255.255.240.0
B. 255.255.248.0
C. 255.255.252.0
D. 255.255.254.0
E. 255.255.255.0
F. 255.255.255.192
A. IP address:192.168.20.14 Subnet Mask:255.255.255.248 Default Gateway:192.168.20.9
B. IP address:192.168.20.254 Subnet Mask:255.255.255.0 Default Gateway:192.168.20.1
C. IP address:192.168.20.30 Subnet Mask:255.255.255.248 Default Gateway:192.168.20.25
D. IP address:192.168.20.30 Subnet Mask:255.255.255.240 Default Gateway:192.168.20.17
E. IP address:192.168.20.30 Subnet Mask:255.255.255.240 Default Gateway:192.168.20.25
A. STP
B. VTP
C. GVRP
D. SNMP
E. DHCP
A network administrator is trying to add a new router into an established OSPF network.The networks attached to the new router do not appear in the routing tables of the other OSPF routers.Given the information in the partial configuration shown below,what configuration error is causing this problem?（）
Router(config)#router ospf 1
Router(config-router)#network 10.0.0.0 255.0.0.0 area 0
A. The process id is configured improperly
B. The OSPF area is configured improperly
C. The network wildcard mask is configured improperly
D. The network number is configured improperly
E. The AS is configured improperly
F. The network subnet mask is configuerd improperly
最新試題
Which command is used to display the collection of OSPF link states?（）
A network administrator is trying to add a new router into an established OSPF network.The networks attached to the new router do not appear in the routing tables of the other OSPF routers.Given the information in the partial configuration shown below,what configuration error is causing this problem?（）Router(config)#router ospf 1Router(config-router)#network 10.0.0.0 255.0.0.0 area 0
A network administrator needs to configure a serial link between the main office and a remote location.The router at the remote office is a non-cisco router. How should the network administrator configure the serial interface of the main office router to make the connection?（）
A router receives information about network 192.168.10.0/24 from multiple sources.What will the router consider the most reliable information about the path to that network?（）
Three switches are connected to one anther via trunk ports.Assuming the default switch configuration,which switch is elected as the root bridge for the spanning-tree instance of vlan 1?（）
A network administrator is planning a network installation for a large organization.The design requires 100 separate subnetworks,so the company has acquired a Class B network address.What subnet mask will provide the 100 subnetworks required, if 500 usable host addresses are required per subnet?（）
What is the result of issuing the frame-relay map ip 192.168.1.2 202 broadcast command?（）
Which cisco ios command can help to determine the timing of various debug events,relative to each other,when you are debugging a complicated router issue?（）
Which statement is true, as relates to classful or classless routing?（）
When you are troubleshooting an ACL issue on a router,which command can help you to verify which interfaces are affected by the ACL?（）