The BGP routing table consists of the following network routes：
What is the correct command to summarize these prefixes into a single summary prefix of192.168.12.0/22 while also allowing for the advertisement of the more specific prefixes？（）
A.network 192.168.12.0 mask 255.255.252.0
B.network 192.168.12.0 mask 0.0.3.255
C.network 192.168.12.0
D.aggregate-address 192.168.12.0 255.255.252.0
E.aggregate-address 192.168.12.0 255.255.252.0 summary-only
F.aggregate-address 192.168.12.0 255.255.252.0 as-set
您可能感興趣的試卷
你可能感興趣的試題
A.A peer router running IBGP
B.A peer router running EBGP
C.A community member running IBGP
D.A peer group member running IBGP
E.A peer group member running EBGP
A BGP router is configured as shown below：
interface ethernet 0
ip address 10.10.10.1 255.255.0.0!
int serial 0
ip address 172.16.1.1 255.255.255.252!
router bgp 65001
neighbor 192.168.1.1 remote-as 65002
Based on the above configuration， which of the following BGP statements would inject the10.10.0.0/16 prefix into the BGP routing table？（）
A.network 10.0.0.0
B.network 10.10.0.0 mask 255.255.0.0
C.network 10.10.10.1 mask 255.255.255.255
D.network 10.10.10.0 mask 255.255.255.0
E.network 10.0.0.0 mask 255.255.0.0
A.The IBGP routers must always be fully meshed
B.The IBGP routers can be in a different AS
C.The IBGP routers must be directly connected
D.The IBGP routers do not need to be directly connected
E.None of the other alternatives apply are true
The network consists of two separate autonomous systems as shown below：
You need to configure Router R2 as a BGP route reflector and Router R1 as the client. Assumingthat Router R3 isn’t running BGP， which two of the commands below would you enter on R2 tosatisfy your goals？（）
A.neighbor 165.50.12.1 remote-as 65100
B.neighbor 165.50.12.2 remote-as 64000
C.neighbor 165.50.12.1 route-reflector-client
D.neighbor 165.50.12.2 route reflector-client
Refer to the exhibit. All routers are configured for BGP. EBGP routes received on router R2 showup in the BGP table on routers R1 and R3 but not in their IP routing tables. What would causethis？（）
A.EBGP multihop is not configured on routers R1 and R3
B.Routers R1 and R3 do not receive the same routes via an IGP
C.Synchronization in autonomous system 100 is turned is on
D.The BGP routers in autonomous system 100 are not logically fully-meshed
E.Synchronization in autonomous system 100 is turned is off
最新試題
You need to configure a GRE tunnel on a IPSec router. When you are using the SDM to configurea GRE tunnel over IPsec， which two parameters are required when defining the tunnel interfaceinformation？（）
Drag the DSL local loop topic on the left to the correct descriptions on the right.
Drag the DSL technologies on the left to their maximum（down/up） data rate values on the below.
Identify the recommended steps for worm attack mitigation by dragging and dropping them into thetarget area in the correct order.
Drag and drop the xDSL type on the above to the appropriate xDSL description on the below.
Which two encapsulation methods require that an 827 ADSL router be configured with a PPPusername and CHAP password？（）
A new router was configured with the following commands：The configuration above was found on an Internet Service Provider’s （ISP） Multiprotocol LabelSwitching （MPLS） network. What is its purpose？（）
cisco ios command to interface dialer 0
Drag and drop the steps in the process for provisioning a cable modem to connect to a headendon the above to the below in the order defined by the DOCSIS standard.
Study the exhibit carefully. The Cisco IOS IPsec High Availability （IPsec HA） Enhancementsfeature provides an infrastructure for reliable and secure networks to provide transparent availability of the VPN gateways - that is， Cisco IOS Software-based routers. What are the twooptions that are used to provide High Availability IPsec？（）