You need to configure a new Company switch for trunking.
Which switch command enables a trunking protocol that appends a four byte CRC to the packet？（）
A. CompanySwitch（config-if）#switchport trunk encapsulation dot1q
B. CompanySwitch（config-if）#switchport trunk encapsulation itef
C. CompanySwitch（config-if）#switchport trunk encapsulation fddi
D. CompanySwitch（config-if）#switchport trunk encapsulation isl
E. None of the other alternatives apply
您可能感興趣的試卷
你可能感興趣的試題
Switch R1 has been configured with DTP using the desirable option.
Which statement describes Dynamic Trunking Protocol （DTP） desirable mode？（）
A. The interface actively attempts to convert the link to a trunk link.
B. The interface is put into permanent trunking mode but prevented from generating DTP frames.
C. The interface is put into permanent trunking mode and negotiates to convert the link into a trunk link.
D. The interface is put into a passive mode， waiting to convert the link to a trunk link.
E. None of the other alternatives apply
The core Company switches are configured to use 802.1Q trunks.
Which three statements are correct with regard to the IEEE 802.1Q standard？（）
A. The IEEE 802.1Q frame format adds a 4 byte field to a Ethernet frame
B. The packet is encapsulated with a 26 byte header and a 4 byte FCS
C. The protocol uses point-to-multipoint connectivity
D. The protocol uses point-to-point connectivity
E. The IEEE 802.1Q frame uses multicast destination of 0x01-00-0c-00-00
F. The IEEE 802.1Q frame retains the original MAC destination address
Refer to the exhibit. On the basis of the output generated by the show commands，
which two statements are true？（）
A. Because it is configured as a trunk interface， interface gigabitethernet 0/1 does not appear in the show vlan output.
B. VLAN 1 will not be encapsulated with an 802.1q header.
C. There are no native VLANs configured on the trunk.
D. VLAN 2 will not be encapsulated with an 802.1q header.
E. All interfaces on the switch have been configured as access ports.
F. Because it has not been assigned to any VLAN， interface gigabitethernet 0/1 does not appear in the show vlan output.
The Company core switches use 802.1Q trunks to connect to each other.
How does 802.1Q trunking keep track of multiple VLANs？ （）
A. It tags the data frame with VLAN information and recalculates the CRC value
B. It encapsulates the data frame with a new header and frame check sequence
C. It modifies the port index of a data frame to indicate the VLAN
D. It adds a new header containing the VLAN ID to the data frame
E. None of the other alternatives apply
Two Company switches are connected via a trunk link. In this network， the original frame is encapsulated and an additional header is added before the frame is carried over a trunk link. At the receiving end， the header is removed and the frame is forwarded to the assigned VLAN.
This describes which technology？（）
A. DISL
B. ISL
C. DTP
D. IEEE 802.1Q
E. MPLS
F. None of the other alternatives apply
最新試題
Refer to the exhibit. Based on the output of the show spanning-tree command， which statement is true？ （）
Based on the show spanning-tree vlan 200 output shown in the exhibit， which two statements about the STP process for VLAN 200 are true？ （）
During routine maintenance， G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However， after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ？ （）
Refer to the exhibit and the partial configuration of switch SW_A and SW_B. STP is configured on all switches in the network. SW_B receives this error message on the console port：00：06：34： %CDP-4-DUPLEX_MISMATCH： duplex mismatch discovered on FastEthernet0/5 （not half duplex）， with SW_A FastEthernet0/4 （half duplex） ， with TBA05071417（Cat6K-B） 0/4 （half duplex）. What would be the possible outcome of the problem？（）
What must be the same to make multiple switches part of the same Multiple Spanning Tree （MST）？（）
During routine maintenance， it became necessary to shutdown G1/0/1 on DS1 and DS2. All other interface were up. During this time， DS1 became the active device for Vlan104’s HSRP group. As related to Vlan104’s HSRP group. What can be done to make the group function properly ？ （）
What two things will occur when an edge port receives a BPDU？（）
Which three statements about STP timers are true？（）
Refer to the exhibit. Which statement is true about the output？（）
Refer to the exhibit. All network links are FastEthernet. Although there is complete connectivity throughout the network， Front Line users have been complaining that they experience slower network performance when accessing the server farm than the Reception office experiences. Based on the exhibit， which two statements are true？（）