The Company network needs to pass traffic between VLANs.
Which device should be used to accomplish this？ （）
A. Hub
B. Switch
C. Router
D. Bridge
E. None of the other alternatives apply
您可能感興趣的試卷
你可能感興趣的試題
pany has implemented numerous multilayer switches that utilize FIB tables.
Which statement is true about the Forward Information Base （FIB） table？（）
A. The FIB is derived from the IP routing table and is optimized for maximum lookup throughput.
B. The FIB table is derived from the Address Resolution Protocol table， and it contains Layer 2 rewrite （MAC） information for the next hop.
C. When the FIB table is full， a wildcard entry redirects traffic to the Layer 3 engine.
D. The FIB lookup is based on the Layer 2 destination MAC address.
E. None of the other alternatives apply
Refer to the exhibit.
What type of attack is being defended against？ （）
A. snooping attack
B. rogue device attack
C. STP attack
D. VLAN attack
E. spoofing attack
F. MAC flooding attack
Refer to the exhibit.
What will happen to traffic within VLAN 14 with a source address of 172.16.10.5？（）
A. The traffic will be forwarded to the router processor for further processing.
B. The traffic will be dropped.
C. The traffic will be forwarded to the TCAM for further processing.
D. The traffic will be forwarded without further processing.
Refer to the exhibit.
What will happen when one more user is connected to interface FastEthernet 5/1？（）
A. The first address learned on the port will be removed from the secure address list and be replaced with the new address.
B. All secure addresses will age out and be removed from the secure address list. This will cause the security violation counter to increment.
C. The packets with the new source addresses will be dropped until a sufficient number of secure MAC addresses are removed from the secure address list.
D. The interface will be placed into the error-disabled state immediately， and an SNMP trap notification will be sent.
Refer to the exhibit. The show port-security interface fa0/1 command was issued on switch SW1. Given the output that was generated，
which two security statement are true？ （）
A. Interface FastEthernet 0/1 was configured with the switchport port-security aging command.
B. Interface FastEthernet 0/1 was configured with the switchport port-security protect command.
C. Interface FastEthernet 0/1 was configured with the switchport port-security violation restrict command.
D. When the number of secure IP addresses reaches 10， the interface will immediately shut down.
E. When the number of secure MAC addresses reaches 10， the interface will immediately shut down and an SNMP trap notification will be sent.
最新試題
DS2 has not become the active device for Vlan103’s HSRP group even though all interfaces are active. As related to Vlan103’s HSRP group. What can be done to make the group function properly ？ （）
Refer to the exhibit. Initially， LinkA is connected and forwarding traffic. A new LinkB is then attached between SwitchA and HubA. Which two statements are true about the possible result of attaching the second link？（）
During routine maintenance， it became necessary to shutdown G1/0/1 on DS1 and DS2. All other interface were up. During this time， DS1 became the active device for Vlan104’s HSRP group. As related to Vlan104’s HSRP group. What can be done to make the group function properly ？ （）
What will occur when a nonedge switch port that is configured for Rapid Spanning Tree does not receive a BPDU from its neighbor for three consecutive hello time intervals？（）
Based on the show spanning-tree vlan 200 output shown in the exhibit， which two statements about the STP process for VLAN 200 are true？ （）
Refer to the exhibit and the partial configuration of switch SW_A and SW_B. STP is configured on all switches in the network. SW_B receives this error message on the console port：00：06：34： %CDP-4-DUPLEX_MISMATCH： duplex mismatch discovered on FastEthernet0/5 （not half duplex）， with SW_A FastEthernet0/4 （half duplex） ， with TBA05071417（Cat6K-B） 0/4 （half duplex）. What would be the possible outcome of the problem？（）
Refer to the exhibit. What does the command channel-group 1 mode desirable do？ （）
During routine maintenance， G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However， after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ？ （）
Refer to the exhibit. Switch 15 is configured as the root switch for VLAN 10 but not for VLAN 20. If the STP configuration is correct， what will be true about Switch 15？（）
Refer to the exhibit. Which statement is true about the output？（）