Routers R1 and R2 are EIGRP neighbors. R1 has been configured with the eigrp stub connected command.
Which of the following is true as a result？（）
A.R1 can learn EIGRP routes from R2, but R2 cannot learn EIGRP routes from R1
B.R1 can send IP packets to R2, but R2 cannot send IP packets to R1
C.R2 no longer learns EIGRP routes from R1 for routes not connected to R1
D.R1 no longer replies to R2's Query messages
E.R2n o longer sends to R1 Query messages
您可能感興趣的試卷
你可能感興趣的試題
Router R1 is three router hops away from subnet 10.1.1.0/24. According to various show interfaces commands, all three links between R1 and 10.1.1.0/24 use the following settings: bandwidth: 1000, 500, 100000 and delay : 12000, 8000, 100.
Which of the following answers correctly identifies a value that feeds into the EIGRP metric calculation？（）
A.Bandwidth of 101,500
B.Bandwidth of about 34,000
C.Bandwidth of 500
D.Delay of 1200
E.Delay of 2010
F.Delay of 20100
A.The configuration of EIGRP offset lists
B.Current link loads
C.Changing interface delay settings
D.Configu ration of variance
Router R1 uses S0/0 to connect via a T/1 to the Frame Relay servicE. Five PVCs terminate on the serial link. Three PVCs (101, 102, and 103) are configured on subinterface S0/0.1, and one each (104 and 105) are on S0/0 .2 and S0/0.3. The configuration shows no configuration related to EIGRP WAN bandwidth control, and the bandwidth command is not configured at all.
Which of the following is true about how IOS tries to limit EIGRP's use of bandwidth on S0/0?（）
A.R1 limi ts EIGRP to around 250Kbps on DLCI 102
B.R1 limits EIGRP to around 250Kbps on DLCI 104
C.R1 limits EIGRP to around 150Kbps on every DLCI
D.R1 does not limit EIGRP because noWAN bandwidth control has been configured
A.Jitter
B.Delay
C.MTU
D.Reliability
最新試題
Which of the following are true of both OSPFv2 and OSPFv3?（）
Which of the following IPv6 tunneling mechanisms support IPv6 IGP routing protocols?（）
Router R1 sits at an Enterprise branch office, using both the Internet and a leased line to another Enterprise router for its two connectivity options back into the rest of the Enterprise network. The engineer planning for this branch decided to use the leased line for all Enterprise traffic, unless it fails, in which case the Internet connection should be used to pass traffic to the Enterprise.Which of the following is most likely to be useful on the branch router?（）
An engineer is trying to summarize the following networks using the "ip summary- address eigrp"command:10.8.88.0/2510.8.89.48/2910.8.64.96/27Which network and subnet mask below would be the smallest EIGRP summary address to include all three subnets?（）
An enterprise has plans to start adding IPv6 support. The initial deployment requires support from some IPv6 - only device s that need to access servers that support only IPv4.Which of the following tools would be most appropriate?（）
The following configura tion exists on a router on one end of an IPv6 tunnel. Which type of tunnel is created by this configuration?（）interface loopback 1ip address 1.1.1.1 255.255.255.255interface tunnel 2ipv6 address 2000::1::/64tunnel source loopback 1tunnel destina tion 2.2.2.2tunnel mode ipv6ipipv6 eigrp 1
Look at the following configuration below and select the statements that are true.（）RD2(config)#router ospf 100RD2(config - router)# distance 180 10.1.10.1 0.0.0.0 match - meRD2(config -router)#!RD2(config - router) #ip access - list standard match - meRD2(config - std - nacl)# permit host 172.16.0.0
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exis ts in a planning document intended to be used to copy/paste into Router R1 to enable EIGRP for IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about EIGRP for IPv6 on R1 after this configuration has been pasted into R1?（）ipv6 router eigrp 1ipv6 unicast- routinginterface f0/0ipv6 address 2000::1/64ipv6 eigrp 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 eigrp 1
Router R1, a branch router, connects to the Internet using DSL. The engineer plans to use a configuration with a dialer interface. The answers list a feature and interface on which the feature could be configured.Which combinations accurately describe the interface under which a feature will be configured?（）
Which of the following is the shortest valid abbreviation for FE80:0000:0000:0000:0010:0000:0000:0123?（）