單項選擇題While logged into a router you manually shut down the serial 0 interface using the "shutdown" interface configuration command. You then issue the "show interface serial 0" command in exec mode. What could you expect the status of the serial 0 interface to be?()

A. Serial 0 is up, line protocol is up
B. Serial 0 is up, line protocol is down
C. Serial 0 is down, line protocol is down
D. Serial 0 is down, line protocol is up
E. Serial 0 is administratively down, line protocol is down
F. Serial 0 is administratively down, line protocol is up


您可能感興趣的試卷

你可能感興趣的試題

1.單項選擇題

There is a connectivity problem between the serial 0/0 interface of router TESTKING1 and the serial 0/0 interface of TESTKING2. A leased line point to point circuit is installed between these two routers. The output from the "show interface serial 0/0" command is displayed below for each of these routers:

From your observations of the above exhibit, what is the underlying cause of the problem?()

A. The loopback is not set.
B. The serial cable is faulty.
C. The subnet mask is not configured properly.
D. The IP address is not configured properly.
E. The Layer 2 frame types are not compatible.
F. The keepalive setting is not configured properly.

2.單項選擇題

The relevant configuration files for the TestKing1 and TestKing2 routers are displayed below:
With due consideration to the command outputs, which of the following reasons would you attribute the connectivity problem between the two routers?()

A. The authentication needs to be changed to PAP for both routers.
B. The serial IP addresses of routers are not on the same subnet.
C. The username/password combination is incorrectly configured.
D. The router names are incorrectly configured.

3.單項選擇題What kind of message does a PING send out to test connectivity?()

A. ICMP echo request
B. Information interrupt request
C. Timestamp reply
D. Source quench
E. None of the above

最新試題

Given a subnet mask of 255.255.255.224, which of the following addresses can be assigned to network hosts?()

題型:多項選擇題

A network host is configured as follows: Host IP address: 192.168.16.183 Subnet mask: 255.255.255.224 Default gateway: 192.168.16.190 Which of the following statements describe the network to which this host is attached?()

題型:多項選擇題

What is the purpose of typing o/r 0x2142 during a password recover procedure on a 2500 series router?()

題型:單項選擇題

Which of the following correctly describe steps in the OSI data encapsulation process?()

題型:多項選擇題

New switches have been purchased for a network upgrade. The objective for the network design emphasizes efficient, error-free transport instead of fast transport.Which switching mode should be configured on the new switches to provide error-free transport to the network? ()

題型:單項選擇題

What does a configuration Register Setting of 0x2105 indicate to the Router? ()

題型:單項選擇題

TestKing.com has allocated the IP add 199.144.27.0 is its network, to provide flexibility for the LAN design, a subnet mask of 255.255.255.240 has been chosen. Which of the following address can be assigned to LAN on the resulting subnets.()

題型:多項選擇題

Which of the following if addresses can be assigned to host devices?()

題型:多項選擇題

The following access list was applied outbound on he E0 interface connected to the 192.168.1.8/29 LAN:access-list 123 deny tcp 192.168.1.8 0.0.0.7 eq 20 anyaccess-list 123 deny tcp 192.168.1.9 0.0.0.7 eq 21 anyWhat effect will this access list have?()

題型:單項選擇題

A Router with a BRI/T interface will be used for an ISDN Connection what other ISDN device is required to complete this connection? ()

題型:單項選擇題