A. Link LSA
B. Interarea prefix LSA for ABRs
C. Router LSA
D. Switch LSA
E. Intra - area prefix LSA
F. None of the above
您可能感興趣的試卷
你可能感興趣的試題
A. a request made by a node to join a specified multicast group
B. a request made by a node for its IP address
C. a request made by a node for the IP address of the DHCP server
D. a request made by a node for the IP address of the local router
To enable BGP tunneling over an IPv4 backbone, the IPv4 address 192.168.30.1 is converted into a valid IPv6 address.
Which three IPv6 addresses are acceptable formats for the IPv4 address? （）
A. 192.168.3 0.1:0:0:0:0:0:0
B. 0:0:0:0:0:0:192.168.30.1
C. ::192.168.30.1
D. C0A8:1E01::
E. 192.168.30.1::
F. ::C0A8:1E01
Refer to the exhibit. Based on the output from the show command on RT1which statement is true? （）
A. OSPFv3 uses global IPv6 addresses to establish neighbor adjacencies.
B. RT1 has a subnet mask of 64 bits .
C. RT1 has FastEthernet0/0 set as a DR for network type broadcast.
D. OSPFv3 uses Link - local addresses to establish neighbor adjacencies.
E. RT1does not have a global IPv6 address set on FastEthernet0/0.
F. OSPFv3 uses IPv4 addresses to establish nei ghbor adjacencies.
A. It must be issued before the network command to enable the OSPF pr ocess for IPv6.
B. It must be issued after the network command to enable the OSPF process for IPv6.
C. It must be issued in router global configuration mode to enable the OSPF process for IPv6.
D. It must be issued in interface configuration mode to ena ble the OSPF process for IPv6.
In IPv6, the interfaces running OSPF can be configured with multiple ad dress prefixes.
Which statement is true about the IPv6 addresses that can be included into the OSPF process?" （）
A. Specific addresses can be selected using a prefix list.
B. Specific addresses can be selected using a route map.
C. Specific addresses cann ot be selected for importation into the OSPF process.
D. Specific addresses can be selected using an ACL.
最新試題
Which of the following answers lists a multicast IPv6 address?（）
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exis ts in a planning document intended to be used to copy/paste into Router R1 to enable EIGRP for IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about EIGRP for IPv6 on R1 after this configuration has been pasted into R1?（）ipv6 router eigrp 1ipv6 unicast- routinginterface f0/0ipv6 address 2000::1/64ipv6 eigrp 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 eigrp 1
Router R1 use s MAC address 1111.1111.1111 for its Fa0/0 interface. An engineer sees the following configuration in the output of a show running - config command. Then, the engineer issues a show ipv6 interface brief command. What global unicast IPv6 address does this c ommand display for interface tunnel 1?（）interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 1tunnel source loopback 1tunnel destination 192.168.1.2tunnel mode ipv6ip isatapipv6 address 2000::/64 eui - 64
Router R1, a branch router, connects to the Internet using DSL. The engineer plans to use a configuration with a dialer interface. The answers list a feature and interface on which the feature could be configured.Which combinations accurately describe the interface under which a feature will be configured?（）
An ISP has assigned prefix 3000:1234:5678::/48 to Company1. Which of the following terms would typically be used to describe this type of public IPv6 prefix?（）
Which of the following is helpful to allow an IPv6 host to learn the IP address of a default gateway on its subnet?（）
Which of the following IPv6 tunneling mechanisms support IPv6 IGP routing protocols?（）
The following line of output was gathered on Enterprise Router Ent1 using the command show ip route. Which of the following answers is most likely to be true, based on thi s output？（）B 128.107.0.0 [20/10] via 11.11.11.11, 00:02:18
Router R1 has two LAN interfaces and three serial interfaces enabled for IPv6. All the inte rfaces use link local addresses automatically generated by the router.Which of the following could be the link local address of R1's interface S0/0?（）
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?（）ipv6 router ospf 1ipv6 unicast- routinginterface f0/0ipv6 address 2000 ::1/64ipv6 ospf 1 area 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 ospf 1 area 0