Jitter is causing problems with the VOIP application in the Company network.
What causes network jitter？（）
A.Variable queue delays
B.Packet drops
C.Transmitting too many small packets
D.Compression
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit. A trunk link is connected between switch A_SW and switch D_SW. Based on the configuration shown in the exhibit，
how would the traffic coming from the switch A_SW be managed？ （）
A.The trunk port Fa0/1 on switch A_SW will trust allCoS values on the frames coming from the IP phone.
B.The trunk port Fa0/1 on switch A_SW will trust allCoS values on the frames received on the IP phone.
C.The trunk port Fa0/1 on switch D_SW will trust allCoS values on the frames coming from port Fa0/1 on A_SW.
D.The trunk port Fa0/1 on switch D_SW will trust allCoS values on the frames received on the A_SW switch port Fa0/4.
E.The trunk port Fa0/1 on switch D_SW will trust allCoS values on the frames received on the IP phone port.
Refer to the exhibit.
Which statement is true when voice traffic is forwarded on the same VLAN used by the data traffic？ （）
A.The voice traffic cannot be forwarded to the distribution layer.
B.The voice traffic cannot use 802.1p priority tagging.
C.Port security cannot be enabled on the switch that is attached to the IP phone.
D.Quality of service cannot be applied for the voice traffic.
Refer to the exhibit.
Why does the trust state of interface FastEthernet 0/3 show "not trusted"？ （）
A.DSCP map needs to be configured for VOIP.
B.ToS has not been configured.
C.ToS has been misconfigured.
D.The command mls qos needs to be turned on in global configuration mode.
E.There is not a Cisco Phone attached to the interface.
Refer to the exhibit.
What statement is true about the configuration on switch CAT1？（）
A.The configuration establishes policed DSCP on ports Fa0/11 and Fa0/12 with values ranging from 8 to 56.
B.The configuration overrides 802.1p priorities on packets entering ports Fa0/11 and Fa0/12 with a value of 48.
C.Untagged Port VLAN ID （PVID） frames will carry voice traffic on VLAN 40.
D.Two IP phones with the MAC addresses of 0008.8595.d1a7 and 0007.8595.d2b7 are connected to CAT1 ports Fa0/11 and Fa0/12， respectively.
E.Security violation shutdown mode has been activated for ports Fa0/11 and Fa0/12.
F.The configuration overrides the Quality of Service value in packets entering ports Fa0/11 and Fa0/12 with a value of 45.
You need to configure a new Cisco router to be installed in the Company VOIP network.
Which three interface commands will configure the switch port to support a connected Cisco phone and to trust the CoS values received on the port if CDP discovers that a Cisco phone is attached？ （）
A.switchport voice vlan vlan-id
B.mls qos trust device cisco-phone
C.switchport priority extend cos_value
D.mls qos trust cos
E.mls qos trust override cos
最新試題
Which statement is correct about the use of the virtual interface on a WLC ？（）
Which three statements are true of the Link Aggregation Control Protocol （LACP）？（）
DS2 has not become the active device for Vlan103’s HSRP group even though all interfaces are active. As related to Vlan103’s HSRP group. What can be done to make the group function properly ？ （）
During routine maintenance， it became necessary to shutdown G1/0/1 on DS1 and DS2. All other interface were up. During this time， DS1 became the active device for Vlan104’s HSRP group. As related to Vlan104’s HSRP group. What can be done to make the group function properly ？ （）
Which option correctly identifies the Cisco IOS switching methods in descending order from the fastest method to the slowest method？（）
Refer to the exhibit. Based on the output of the show spanning-tree command， which statement is true？ （）
Refer to the exhibit. LACP has been configured on Switch1 as shown. Which is the correct command set to configure LACP on Switch2？（）
Refer to the exhibit. The command switchport mode access is issued on interface FastEthernet0/13 on switch CAT1. What will be the result？（）
Examine the diagram. A network administrator has recently installed the above switched network using 3550s and would like to control the selection of the root bridge.Which switch should theadministrator configure as the root bridge and which configuration command must theadministrator enter to accomplish this？（）
Refer to the exhibit. What does the command channel-group 1 mode desirable do？ （）