Refer to the exhibit.
Which switch interface configuration command would automatically configure quality of service （QoS） for voice over IP （VoIP） within a QoS domain？ （）
A.switchport priority extend trust
B.mls qos trust
C.switchport priority extend cos 7
D.auto qos voip cisco-phone
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit. A trunk link is connected between switch A_SW and switch D_SW. Based on the configuration shown in the exhibit，
how would the traffic coming from the switch A_SW be managed？（）
A.The trunk port Fa0/1 on switch A_SW will trust allCoS values on the frames coming from the IP phone.
B.The trunk port Fa0/1 on switch A_SW will trust allCoS values on the frames received on the IP phone.
C.The trunk port Fa0/1 on switch D_SW will trust allCoS values on the frames coming from port Fa0/1 on A_SW.
D.The trunk port Fa0/1 on switch D_SW will trust allCoS values on the frames received on the A_SW switch port Fa0/4.
E.The trunk port Fa0/1 on switch D_SW will trust allCoS values on the frames received on the IP phone port.
The Company network is displayed in the following topology exhibit：
Workstation 1 traffic is set for cos 5 and the switch CompanyA sends workstation 1 traffic to the switch CompanyB. However， not all of the traffic from Switch CompanyA is from workstation 1. Switch CompanyA configurations Switch CompanyB Configuration：
mlsqos mls qos
interfacefa0/1 interface fa0/1
switchportmode trunk switchport trunk mode
switchporttrunk encapsulation dot 1q switchport trunk encapsulation dot 1q
switchporttrunk native vlan 1 switchport trunk native vlan 1
Frames from Workstation 1 are given the rightful priority through Switch CompanyA， but Switch CompanyB doesn’t reciprocate， and treats Workstation 1 frames as if they have no precedence. Which of the following actions will prioritize traffic from Workstation 1？（）
A. Configure qos all command under Switch CompanyB fa0/1 interface.
B. Configure mls qos trust cos command under Switch CompanyB fa0/1 interface.
C. Configure mls qos trust cos 5 command under Switch CompanyB fa0/1 interface.
D. Configure qos cos 5 command under Switch CompanyB fa0/1 interface.
E. Configure mls qos trust cos command under Switch CompanyA fa0/1 interface.
F. Configure qos cos 5 command under Switch CompanyA fa0/1 interface.
VOIP is being implemented in the Company network and you need to assess the need for QoS.
Which of the following network problems would indicate a need to implement QoS features？（）
A.Mis-routed packets
B.Excess jitter
C.Delay of critical traffic
D.Packet loss due to congestion
E.Data link layer broadcast storms
F.FTP connections unsuccessful
VOIP is being implemented on the Company network. In a properly designed network，
what is the maximum amount of time a voice package should spend crossing a network？ （）
A.90 milliseconds
B.120 milliseconds
C.150 milliseconds
D.240 milliseconds
Jitter is causing problems with the VOIP application in the Company network.
What causes network jitter？（）
A.Variable queue delays
B.Packet drops
C.Transmitting too many small packets
D.Compression
最新試題
Which two statements about the various implementations of STP are true？（）
What two things will occur when an edge port receives a BPDU？（）
Refer to the exhibit. LACP has been configured on Switch1 as shown. Which is the correct command set to configure LACP on Switch2？（）
Which three statements about STP timers are true？（）
During routine maintenance， it became necessary to shutdown G1/0/1 on DS1 and DS2. All other interface were up. During this time， DS1 became the active device for Vlan104’s HSRP group. As related to Vlan104’s HSRP group. What can be done to make the group function properly ？ （）
Refer to the exhibit and the partial configuration of switch SW_A and SW_B. STP is configured on all switches in the network. SW_B receives this error message on the console port：00：06：34： %CDP-4-DUPLEX_MISMATCH： duplex mismatch discovered on FastEthernet0/5 （not half duplex）， with SW_A FastEthernet0/4 （half duplex） ， with TBA05071417（Cat6K-B） 0/4 （half duplex）. What would be the possible outcome of the problem？（）
Refer to the exhibit. What command was issued on the Layer 3 switch Sw1 between Exhibit #1 and Exhibit #2？（）
Refer to the exhibit. Based on the output of the show spanning-tree command， which statement is true？ （）
Refer to the exhibit. The command switchport mode access is issued on interface FastEthernet0/13 on switch CAT1. What will be the result？（）
What will occur when a nonedge switch port that is configured for Rapid Spanning Tree does not receive a BPDU from its neighbor for three consecutive hello time intervals？（）