Refer to the exhibit. Which two conclusions can be drawn from the debug ip igmp output?()
A. The router sent an IGMP version 2 query out interface Ethernet1 at multicast address 224.0.0.1.
B. Router RTA received an IGMP report version 1 from host 192.168.9.1.
C. Reverse Path Forwarding (RPF) is ena bled for 192.168.9.4.
D. Reverse Path Forwarding (RPF) is enabled for 224.0.1.40.
E. The IP multicast groups are 224.0.0.1, 224.0.1.40, and 239.255.0.1.
F. IP PIM RP mapping is static.
您可能感興趣的試卷
你可能感興趣的試題
A. IGMP
B. IGMP snooping
C. PIM
D. CGMP
E. static assignment
F. CDP
A. Sparse mode multicast uses a pull model to send multicast traffic to where it is requested
B. Dense mode multicast uses a push model to flood traffic throughout the network and then prunes the unwanted traffic
C. Dense mode multicast requires explicit join messa ges from their members
D. Sparse mode uses reverse path forwarding (RPF) to prune off redundant flows
E. The primary use of sparse mode multicast is for test labs and router performance testing
A. The multicast sources must register with the RP to form the multicast distribution tree
B. An RP is required only in networks running Protocol Independent Multicast dense mode ( PIM DM)
C. The multicast receivers must register with the RP to form the multicast distribution tree
D. An RP is required only in networks running Protocol Independent Multicast sparse mode (PIM SM)
E. An RP is required only in networks running Pro tocol Independent Multicast sparse - dense mode (PIM - SDM)
F. To form the multicast distribution tree, the multicast sources register with and the receivers join the RP
Refer to the exhibit. All routers have Protocol Independent Multicast (PIM) enabled interfaces. On the basis of the configuration provided on routers R1 and R2, which router will take on the func tion of rendezvous point (RP) for the multicast network? ()
A. both routers R1 and R2
B. router R1
C. router R2
D. none of the routers since they are not configured with static RP
Refer to the network of Layer 3 switches in the exhibit. The RPI Multi cast Server only multicasts to hosts connected to multilayer switches 5 and 6. The CMU Multicast Server multicasts to hosts on multilayer switches 1 - 6. Given the number of configuration steps involved, what is the most efficient way to configure the net work while meeting the requirements for multicast data flow? ()
A. Configure each switch with PIM sparse mode and a separate instance of PIM dense mode.Specify switch 1 as the root for the RPI Multicast Server. Specify switch 2 as the root for the CMU Multicast Server.
B. Configure each switch with PIM sparse mode and a separate instance of PIM dense mode. Leave each multicast server as the root of its own multicast tree.
C. Configure each switch with PIM sparse - dense mode. Configure switch 3 as a ren dezvous point for the RPI multicast stream.
D. Configure each switch with PIM sparse mode and a separate instance of PIM dense mode.Allow the switches to elect their own root for each multicast tree.
E. Configure each switch with PIM sparse mode.
F. Configure each switch with PIM dense mode.
最新試題
Router R1 lists the following output from a show command. Which of the following is true about R1?()R1# show ip v6 interface f0/0FastEthernet0/0 is up, line protocol is upIPv6 is enabled, link - local address is FE80::213:19FF:FE12:3456No Virtual link - local address(es):Global unicast address(es):2000::4:213:19FF:FE12:3456, subnet is 2000:0:0:4::/64 [EUI]Jo ined group address(es):FF02::1FF02::2FF02::1:FF:12:3456
Router R1 sits at an Enterprise branch office, using both the Internet and a leased line to another Enterprise router for its two connectivity options back into the rest of the Enterprise network. The engineer planning for this branch decided to use the leased line for all Enterprise traffic, unless it fails, in which case the Internet connection should be used to pass traffic to the Enterprise.Which of the following is most likely to be useful on the branch router?()
The following configuration exists on a router on one end of an IPv6 tunnel. Although the configuration added so far is correct, the configuration is incomplete. Which type of tunnel is most likely to be intended by the network engineer?()interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 2ipv6 address 2002:C0A8:10 1::1/64tunnel source loopback 1
Look at the following configuration below and select the statements that are true.()RD2(config)#router ospf 100RD2(config - router)# distance 180 10.1.10.1 0.0.0.0 match - meRD2(config -router)#!RD2(config - router) #ip access - list standard match - meRD2(config - std - nacl)# permit host 172.16.0.0
An engineer is reviewing another engineer's sample configuration for a GRE tunnel used to pass IPv6 traffiC. The tunnel ha s not yet been configured on the router.Which of the following commands is not required for the configuration to pass IPv6 traffic?()
Router R1 connects to Router R2 over an Ethernet LAN with both routers using their F0/0 interfaces. R1 learns a route from R2 using EIGRP f or IPv6. That route lists F0/0 as the outgoing interface with R2 as the next hop. The configuration excerpt shows all relevant configuration on R2's F0/0 interface. Which of the following is true about R1's route?()interface f0/0mac - address 1111.1111.1 111ipv6 address 2000::/64 eui - 64ipv6 address 2001::1/64
Which of the following features work the same in both RIP- 2 and RIPng?()
The following output on Router R1 lists details of a BGP route for 190.1.0.0/16. Which of the following is true based on this output?()R1# show ip bgp 19 0.1.0.0/16BGP routing table entry for 190.1.0.0/16, version 121Paths: (1 available, best #1, table Default - IP - Routing - Table)Advertised to update - groups:11 2 3 41.1.1.1 from 2.2.2.2 (3.3.3.3)Origin IGP, metric 0, localpref 100, valid, internal, best
Router R1 has been conf igured with an ipv6 route 2000::/64 S0/0/0 64 command.Which of the following does the 64 at the end of the command represent?()
An enterprise h as plans to start adding IPv6 support. For the first year, the IPv6 will be in small pockets spread around the existing large IPv4 network, with occasional IPv6 traffic while applications teams test IPv6 - enabled servers and applications.Which of the fol lowing tools would be most appropriate?()