To protect against first-hop router failure， four protocols were developed to ensure IP routing redundancy.
Which of the following are they？（）
A. HSRP
B. IRDP
C. ICMP
D. VRRP
E. MSTP
F. GLBP
您可能感興趣的試卷
你可能感興趣的試題
HSRP is being set up between two Company devices.
In what three states is it possible for an HSRP router to be in？（）
A. Standby
B. Established
C. Active
D. Idle
E. Backup
F. Init
R1 and R2 exchange HSRP between each other in the Company network.
In which three HSRP states do routers send hello messages？（）
A. Learn
B. Speak
C. Standby
D. Listen
E. Active
F. Remove
You need to implement a high availability design in the Company routed network.
Which protocol allows for the automatic selection and simultaneous use of multiple available gateways as well as automatic failover between those gateways？（）
A. VRRP
B. GLBP
C. IRDP
D. HSRP
E. None of the other alternatives apply
You need to decide on the best router redundancy protocol to use in the Company network.
Which two statements are true about HSRP， VRRP， and GLBP？（）
A. GLBP and VRRP allow for MD5 authentication， whereas HSRP does not.
B. HSRP allows for multiple upstream active links being simultaneously used， whereas GLBP does not.
C. GLBP allows for router load balancing of traffic from a network segment without the different host IP configurations required to achieve the same results with HSRP.
D. Unlike HSRP and VRRP， GLBP allows automatic selection and simultaneous use of multiple available gateways.
E. GLBP allows for router load balancing of traffic from a network segment by utilizing the creation of multiple standby groups.
Routers R1 and R2 use HSRP so that one router will back up the other should there be a failure.
Which two statements are true about the Hot Standby Router Protocol （HSRP）？ （）
A. Load sharing with HSRP is achieved by creating multiple subinterfaces on the HSRP routers.
B. Routers configured for HSRP can belong to multiple groups and multiple VLANs.
C. Load sharing with HSRP is achieved by creating HSRP groups on the HSRP routers.
D. All routers configured for HSRP load balancing must be configured with the same priority.
E. Routers configured for HSRP must belong to only one group per HSRP interface.
最新試題
What two things will occur when an edge port receives a BPDU？（）
Which two statements are true about BPDU port-guard and BPDU filtering？（）
Refer to the exhibit. What command was issued on the Layer 3 switch Sw1 between Exhibit #1 and Exhibit #2？（）
Refer to the exhibit. Initially， LinkA is connected and forwarding traffic. A new LinkB is then attached between SwitchA and HubA. Which two statements are true about the possible result of attaching the second link？（）
Refer to the exhibit. STP has been implemented in the network. Switch SW_A is the root switch for the default VLAN. To reduce the broadcast domain， the network administrator decides to split users on the network into VLAN 2 and VLAN 10. The administrator issues the command spanning-tree vlan 2 root primary on switch SW_A. What will happen as a result of this change？（）
How are STP timers and state transitions affected when a topology change occurs in an STP environment？（）
Which three statements are true of the Link Aggregation Control Protocol （LACP）？（）
What must be the same to make multiple switches part of the same Multiple Spanning Tree （MST）？（）
Refer to the exhibit. Which Virtual Router Redundancy Protocol （VRRP） statement is true about the roles of the master virtual router and the backup virtual router？（）
Refer to the exhibit. Which statement is true about the output？（）