Refer to the exhibit. HSRP has been configured and Link A is the primary route to router R4. When Link A fails， router R2 （Link B） becomes the active router.
Which router will assume the active role when Link A becomes operational again？" （）
A. The primary router R1 will reassume the active role when it comes back online.
B. The standby router R2 will remain active and will forward the active role to router R1 only in the event of its own failure.
C. The standby router R2 will remain active and will forward the active role to router R1 only in the event of Link B failure.
D. The third member of the HSRP group， router R3， will take over the active role only in event of router R2 failure.
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit. The Gateway Load Balancing Protocol has been configured on routers R1 and R2， and hosts A and B have been configured as shown.
Which statement can be derived from the exhibit？（）
A. The hostA default gateway has been configured as 10.88.1.10/24.
B. The GLBP weighted load balancing mode has been configured.
C. The GLBP round-robin， load-balancing mode has been configured.
D. The GLBP host-dependent， load-balancing mode has been configured.
E. The hostA default gateway has been configured as 10.88.1.1/24.
F. The hostA default gateway has been configured as 10.88.1.4/24.
Which command will need to be added to External_A to ensure that it will take over if serial 0/0 on External_B fails？（）
A. standby 1 priority 130
B. standby 1 preempt
C. standby 1 track fastethernet 0/0
D. standby 1 track 10.10.10.1
Routers can send hello messages in three HSRP states.
Which ones are they？（）
A. Standby
B. Learn
C. Listen
D. Speak
E. Active
Router R1 is configured for HSRP.
Which of the following are valid HSRP states on R1？ （）
A. Init
B. Idle
C. Active
D. Standby
E. Established
F. Backup
You have configured router R1 with HSRP， using the standard defaults.
Which three statements are true of a default HSRP configuration？（）
A. The Standby hello time is 2 seconds.
B. Two HSRP groups are configured.
C. The Standby track interface priority is 10.
D. The Standby hold time is 10 seconds
E. The Standby priority is 100.
F. The Standby delay is 3 seconds.
最新試題
Refer to the exhibit. Based on the output of the show spanning-tree command， which statement is true？ （）
Refer to the exhibit. Initially， LinkA is connected and forwarding traffic. A new LinkB is then attached between SwitchA and HubA. Which two statements are true about the possible result of attaching the second link？（）
Refer to the exhibit. STP has been implemented in the network. Switch SW_A is the root switch for the default VLAN. To reduce the broadcast domain， the network administrator decides to split users on the network into VLAN 2 and VLAN 10. The administrator issues the command spanning-tree vlan 2 root primary on switch SW_A. What will happen as a result of this change？（）
Which two statements are true when the extended system ID feature is enabled？ （）
Refer to the exhibit. LACP has been configured on Switch1 as shown. Which is the correct command set to configure LACP on Switch2？（）
Which statement is correct about the use of the virtual interface on a WLC ？（）
Refer to the exhibit. Switch S2 contains the default configuration. Switches S1 and S3 both have had the command spanning-tree mode rapid-pvst issued on them. What will be the result？（）
Refer to the exhibit. What command was issued on the Layer 3 switch Sw1 between Exhibit #1 and Exhibit #2？（）
Which two statements about the various implementations of STP are true？（）
Refer to the exhibit and the partial configuration of switch SW_A and SW_B. STP is configured on all switches in the network. SW_B receives this error message on the console port：00：06：34： %CDP-4-DUPLEX_MISMATCH： duplex mismatch discovered on FastEthernet0/5 （not half duplex）， with SW_A FastEthernet0/4 （half duplex） ， with TBA05071417（Cat6K-B） 0/4 （half duplex）. What would be the possible outcome of the problem？（）