A. eBGP Multipath
B. eBGP Multihop
C. BGP Synchronization
D. Public AS numbers
您可能感興趣的試卷
你可能感興趣的試題
Refer to the above exhibit. Why are the EIGRP neighbors for this router not learning the routes redistributed from OSPF?（）
A. Redistribution must be enabled mutually (in both directions) to work correctly.
B. auto - summary causes the OSPF routes redistributed into EIGRP to be summarized; thus the OSPF network 116.16.34 is summarized to 116.3 4.0.0, which is already covered by the EIGRP protocol.
C. Default metrics are not configured under EIGRP.
D. Both routing protocols must have unique autonomous system numbers for redistribution to function correctly.
Refer to the above exhibit. Why is the 140.140.0.0 network not used as the gateway of last resort even though it is configured first?（）
A.The last default - network statement will always be preferred.
B.A route to the 140.140.0.0 network does not exist in the routing table.
C.Default - network selection will always prefer the statement with the lowest IP address.
D.A router will load balance across multiple default - networks; repeatedly issuing the show ip route command would show the gateway of last resort changing between the two networks.
A. EIGRP would be appropriate if LMI type ANS I is NOT used.
B. EIGRP would be appropriate, because the Frame Relay spokes could be segmented into their own areas.
C. EIGRP would be appropriate, because by default, queries are not propagated across the slow speed Frame Relay links.
D. EIGRP would be appropriate, because you can manage how much bandwidth is consumed over the Frame Relay interface.
A. A change in the load on an interface will cause EIGRP to recalculate the routing metrics and send a corresponding update out to each of its neighbors.
B. EIGRP calculates interface load as a 5 - minute exponentially weighted average that is updated every 5 minutes.
C. EIGRP considers the load of an interface only when sending an update for some other reason.
D. A change in the load on an interface will cause EIGRP to recalculate and update the administrative distance for all routes learne d on that interface.
Based on the need to limit processing and bandwidth utilization due to dynamic routing protocol operation, the foll owing routing requirements have been specified for your network.
- partial and incremental routing updates
- only the devices affected by a topology change perform route recomputation
- route recomputation only occurs for routes that were affected
Which dynamic routing protocol should be deployed in your network to best meet these requirements?（）
A. BGP
B. OSPF
C. IS - IS
D. EIGRP
E. RIPv2
最新試題
Router R1 sits at an Enterprise branch office, using both the Internet and a leased line to another Enterprise router for its two connectivity options back into the rest of the Enterprise network. The engineer planning for this branch decided to use the leased line for all Enterprise traffic, unless it fails, in which case the Internet connection should be used to pass traffic to the Enterprise.Which of the following is most likely to be useful on the branch router?（）
Which of the following is helpful to allow an IPv6 host to learn the IP address of a default gateway on its subnet?（）
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable RIPng and IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Which of the following is true about RIPng on R1 after this configuration has been pasted into R1?（）ipv6 unicast- routinginterface f0/0ipv6 rip one enableipv6 address 2000::1/64interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 rip one enable
Router R1 lists the following output from a show command. Which of the following is true about R1?（）R1# show ip v6 interface f0/0FastEthernet0/0 is up, line protocol is upIPv6 is enabled, link - local address is FE80::213:19FF:FE12:3456No Virtual link - local address(es):Global unicast address(es):2000::4:213:19FF:FE12:3456, subnet is 2000:0:0:4::/64 [EUI]Jo ined group address(es):FF02::1FF02::2FF02::1:FF:12:3456
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?（）ipv6 router ospf 1ipv6 unicast- routinginterface f0/0ipv6 address 2000 ::1/64ipv6 ospf 1 area 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 ospf 1 area 0
Which of the following answers lists a multicast IPv6 address?（）
Router R1 has the following configuration. Assuming R1's F0/0 interface has a MAC address of 0200.0011.1111, what IPv6 addresses will R1 list for interface F0/0 in the output of the show ipv6 interface brief command?（）interface f0/0ipv6 address 2345:0:0:8::1/64
Router R1, a branch router, connects to the Internet using DSL. The engineer plans to use a configuration with a dialer interface. The answers list a feature and interface on which the feature could be configured.Which combinations accurately describe the interface under which a feature will be configured?（）
The following output on Router R1 lists details of a BGP route for 190.1.0.0/16. Which of the following is true based on this output?（）R1# show ip bgp 19 0.1.0.0/16BGP routing table entry for 190.1.0.0/16, version 121Paths: (1 available, best #1, table Default - IP - Routing - Table)Advertised to update - groups:11 2 3 41.1.1.1 from 2.2.2.2 (3.3.3.3)Origin IGP, metric 0, localpref 100, valid, internal, best
Which of the following features work the same in both RIP- 2 and RIPng?（）