Your boss， Miss ，is interested in CEF.
What should you tell her？ （）
A.The FIB lookup is based on the Layer 3 destination address prefix （shortest match）.
B.The adjacent table is derived from the ARP table.
C.The FIB table is derived from the IP routing table.
D.When the adjacency table is full， a CEF TCAM table entry points to the Layer 3 engine to redirect the adjacency.
E.CEF IP destination prefixes are stored in the TCAM table， from the least specific to the most specific entry.
F.When the CEF TCAM table is full， packets are dropped.
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit. DHCP snooping is enabled for selected VLANs to provide security on the network.
How do the switch ports handle the DHCP messages？（）
A.Ports Fa2/1 and Fa2/2 source DHCP requests only. Port Fa3/1 is eligible to source all DHCP messages and respond to DHCP requests.
B.Ports Fa2/1 and Fa2/2 respond to DHCP requests only. Port Fa3/1 is eligible to source all DHCP messages.
C.Ports Fa2/1 and Fa2/2 are eligible to source all DHCP messages and respond to DHCP requests. Port Fa3/1 can source DHCP request only.
D.All three ports， Fa2/1， Fa2/2， and Fa3/1， are eligible to source all DHCP messages and respond to DHCP requests.
Exhibit：
You work as a network administrator at. You study the exhibit carefully.
Which configuration on the HSRP neighboring device ensures that it becomes the active HSRP device in the event that port fa1/1 on 1 goes down？ （）
A. 2（config-if）#ip address 10.10.10.2 255.255.255.0 2（config-if）#standby 1 priority 200 2（config-if）#standby 1 ip 10.10.10.10
B. 2（config-if）# ip address 10.10.10.2 255.255.255.0 2（config-if）#standby 1 priority 195 2（config-if）#standby 1 preempt 2（config-if）#standby 1 ip 10.10.10.10
C. 2（config-if）# ip address 10.10.10.2 255.255.255.0 2（config-if）#standby 1 priority 190 2（config-if）#standby 1 ip 10.10.10.10 2（config-if）#standby 1 track interface fa 1/1
D. 2（config-if）# ip address 10.10.10.2 255.255.255.0 2（config-if）#standby 1 priority 200 2（config-if）#standby 1 preempt 2（config-if）#standby 1 ip 10.10.10.10 2（config-if）#standby 1 track interface fa 1/1
You have configured the "config network webmode enable" command on a Cisco device.
What is the purpose of this command？ （）
A.To allow HTTP access to the WLAN controller
B.To allow SSH access to the CLI of the WLAN controller
C.To allow SSL access to the CLI of the WLAN controller
D.To allow HTTPS access to the WLAN controller
E.None of the other alternatives apply
A.When the voice VLAN feature is enabled， all untagged voice and data traffic is sent through the voice VLAN.
B.The voice VLAN feature is enabled by default.
C.The IP phone overrides the priority of all incoming data traffic （tagged and untagged） and sets the CoS value to 0.
D.The default CoS value is 1 for incoming voice and data traffic.
You work as a network engineer for. You study the exhibit carefully.
What type of attack would be mitigated by this configuration？（）
A.CDP manipulation
B.VLAN hopping
C.MAC spoofing
D.MAC flood attack
E.ARP spoofing
F.spanning tree compromises
最新試題
Refer to the exhibit and the partial configuration of switch SW_A and SW_B. STP is configured on all switches in the network. SW_B receives this error message on the console port：00：06：34： %CDP-4-DUPLEX_MISMATCH： duplex mismatch discovered on FastEthernet0/5 （not half duplex）， with SW_A FastEthernet0/4 （half duplex） ， with TBA05071417（Cat6K-B） 0/4 （half duplex）. What would be the possible outcome of the problem？（）
Refer to the exhibit. LACP has been configured on Switch1 as shown. Which is the correct command set to configure LACP on Switch2？（）
Which three statements about STP timers are true？（）
What is the configured priority value of the Vlan105’s group on DS2 ？（）
Refer to the exhibit. Initially， LinkA is connected and forwarding traffic. A new LinkB is then attached between SwitchA and HubA. Which two statements are true about the possible result of attaching the second link？（）
Refer to the exhibit. Based on the output of the show spanning-tree command， which statement is true？ （）
During routine maintenance， G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However， after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ？ （）
How are STP timers and state transitions affected when a topology change occurs in an STP environment？（）
DS2 has not become the active device for Vlan103’s HSRP group even though all interfaces are active. As related to Vlan103’s HSRP group. What can be done to make the group function properly ？ （）
If G1/0/1 on DS1 is shutdown， what will be the current priority value of the Vlan105’s group on DS1 ？（）