Refer to the exhibit. You want to use all the routes in the EIGRP topology for IP load balancing. Which two EIGRP subcommands wou ld you use to accomplish this goal?（）
A. traffic - share balanced
B. distance
C. maximum- paths
D. default - network
E. variance
您可能感興趣的試卷
你可能感興趣的試題
A. performing inter - VLAN routing
B. performing 802.1Q trunking
C. performi ng ISL trunking
D. Ethernet Switch Module installed
E. ADSL WIC installed
F. running Call Manager Express
A. PPPoE
B. DOCSIS
C. CMTS
D. AAL5
A. to provide VPN access over L2TP
B. to enable PPP session from the router to the termination device at the headend for metro Ethernet connectivity
C. for DSL connectivity and removing the need for the end - user PC to ru n the PPPoE client software
D. for connecting the router to a cable modem, which bridges the Ethernet frames from the router to the cable modem termination system
A. PPPoA
B. PPPoE
C. PPP
D. L2TP
E. ATM
You have implemented mutual route redistribution between OSPF and EIGRP on a border router. When checking the routing table on one o f the OSPF routers within the OSPF routing domain, you are seeing some, but not all of the expected routes.
Which two things should you verify to troubleshoot this problem?（）
A. The border router is using a proper seed metric for OSPF
B. The border ro uter is using a proper seed metric for EIGRP
C. The administrative distance is set for OSPF and EIGRP
D. The missing EIGRP routes are present in the routing table of the border router
E. The subnet keyword on the border router in the redistribute EIG RP command
最新試題
Which of the following is helpful to allow an IPv6 host to learn the IP address of a default gateway on its subnet?（）
Router R1 has two LAN interfaces and three serial interfaces enabled for IPv6. All the inte rfaces use link local addresses automatically generated by the router.Which of the following could be the link local address of R1's interface S0/0?（）
Router R1 has been conf igured with an ipv6 route 2000::/64 S0/0/0 64 command.Which of the following does the 64 at the end of the command represent?（）
Which of the following IPv6 tunneling mechanisms support IPv6 IGP routing protocols?（）
An enterprise has plans to start adding IPv6 support. The initial deployment requires support from some IPv6 - only device s that need to access servers that support only IPv4.Which of the following tools would be most appropriate?（）
Which of the following features work the same in both RIP- 2 and RIPng?（）
An engineer is reviewing another engineer's sample configuration for a GRE tunnel used to pass IPv6 traffiC. The tunnel ha s not yet been configured on the router.Which of the following commands is not required for the configuration to pass IPv6 traffic?（）
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exis ts in a planning document intended to be used to copy/paste into Router R1 to enable EIGRP for IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about EIGRP for IPv6 on R1 after this configuration has been pasted into R1?（）ipv6 router eigrp 1ipv6 unicast- routinginterface f0/0ipv6 address 2000::1/64ipv6 eigrp 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 eigrp 1
The following output occurs on Router R1 , which runs both EIGRP for IPv6 and OSPFv3, with redistribution from EIGRP into OSPF configured with the redistribute eigrp 1 metric 25 command. Interface S0/0/1 has been enabled for EIGRP ASN 1. Which of the following should be true of redistribution in this case?（）D 2000::/64 [90/1422516]via FE80::213:19FF:FE7B:5026, Serial0/0/1C 2000:0:0:1::/64 [0/0]via Serial0/0/1, directly connectedL 2000::1:213:19FF:FE7B:5004/128 [0/0]via Serial0/0/1, receive
An Enterprise rou ter, Ent1, displays the following excerpt from the show ip bgp command. ENT1 has an eBGP connection to an ISP router with address 3.3.3.3 and an iBGP connection to a router with address 4.4.4.4. Which of the following is most likely to be true?（）Network Next Hop Metric LocPrf Weight Path*> 3.3.3.3 0 0 1 1 1 1 218 i