You want the redistributed EIGRP AS 10 routes to have an administrative distance of 121 when they appear as RIP routes in the routing table of A1.Which command should you use on a router to accomplish this goal?（）
A. redistribute eigrp 10 metric 121
B. redistribute rip metric 121
C. default - metric 121
D. distance 121 10.1.1.6 0.0.0.0
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit. A new TAC engineer comes to you for advice. The engineer wants to configure RIPv2 - OSPF two - way redistribution while avoiding routing loops. Which two additio ns to the router B1 configuration should the engineer make?（）
A. access - list 40 deny 172.16.1.0 0.0.0.255 access - list 40 permit any router rip redistribute ospf 100 metric 5 distribute- list 40 out ospf 100
B. ip prefix - list rip_routes permit 172. 16.1.16/25 ge 26 le 28 route - map redis - ospf deny 10 match ip address prefix- list rip_routes router rip redistribute ospf 10 route - map redis - ospf subnets
C. ip prefix - list rip - to - ospf permit 10.1.1.8/25 ge 26 le 28 route - map redis - rip deny 20 match i p address prefix - list rip - to - ospf router ospf 100 redistribute rip route - map redis - rip subnets
D. access - list 15 deny 10.1.1.0 0.0.0.63 access - list 15 permit any route - map redis - rip deny 10 match ip address 15 route - map redis - rip permit 20 router os pf 100 redistribute rip route - map redis - rip subnets
A. retransmit - interval
B. de ad - interval
C. stub area
D. virtual link
E. NSSA area
A. Routes learned using any IP routing protocol can only be redistributed into non IP routing protocols.
B. OSPF can import routes learned using EIGRP, RIP, and IS - IS.
C. OSPF routes cannot be exported into EIGRP, RIP, an d IS - IS.
D. At the interdomain level, OSPF cannot import routes learned using BGP.
E. OSPF routes can be exported into BGP.
Refer to the exhibit. Currently the two eBGP links between AS100 and AS200 have an average inbound load of 65% and 20% respectively. After further investigation, traffic to 10.10.1.16/28 accounts for 45%, and t raffic to 10.10.1.32/28 and to 10.10.1.48/28 each account for 20% of the inbound load. The BGP attributes are currently set at their default values in both autonomous systems. If you want to influence how AS200 sends traffic to AS100, which eBGP configu rations would you configure in AS100 to influence AS200 to use the eBGP links more evenly?（）
A. neighbor 192.168.30.2 route - map as_50 out
B. neighbor 192.168.20.2 route - map as_50 out
C. route - map as_50 permit 10 match ip address 50 set metric 150 a ccess - list 50 permit 10.10.1.16 0.0.0.240
D. route - map as_50 permit 10 match ip address 50 set metric 150 access - list 50 permit 10.10.1.32 0.0.0.240
Refer to the exhibit. A new TAC engineer came to you for advice. A GRE over IPsec tunnel was configured, but the tunnel is not coming up. W hat did the TAC engineer configure incorrectly?（）
A. The crypto isakmp configuration is not correct.
B. The crypto map configuration is not correct.
C. The interface tunnel configuration is not correct.
D. The network configuration is not correct; netw ork 172.16.1.0 is missing.
最新試題
The following line of output was gathered on Enterprise Router Ent1 using the command show ip route. Which of the following answers is most likely to be true, based on thi s output？（）B 128.107.0.0 [20/10] via 11.11.11.11, 00:02:18
Which of the following is helpful to allow an IPv6 host to learn the IP address of a default gateway on its subnet?（）
Router R1 use s MAC address 1111.1111.1111 for its Fa0/0 interface. An engineer sees the following configuration in the output of a show running - config command. Then, the engineer issues a show ipv6 interface brief command. What global unicast IPv6 address does this c ommand display for interface tunnel 1?（）interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 1tunnel source loopback 1tunnel destination 192.168.1.2tunnel mode ipv6ip isatapipv6 address 2000::/64 eui - 64
The following output occurs on Router R1 , which runs both EIGRP for IPv6 and OSPFv3, with redistribution from EIGRP into OSPF configured with the redistribute eigrp 1 metric 25 command. Interface S0/0/1 has been enabled for EIGRP ASN 1. Which of the following should be true of redistribution in this case?（）D 2000::/64 [90/1422516]via FE80::213:19FF:FE7B:5026, Serial0/0/1C 2000:0:0:1::/64 [0/0]via Serial0/0/1, directly connectedL 2000::1:213:19FF:FE7B:5004/128 [0/0]via Serial0/0/1, receive
The following configura tion exists on a router on one end of an IPv6 tunnel. Which type of tunnel is created by this configuration?（）interface loopback 1ip address 1.1.1.1 255.255.255.255interface tunnel 2ipv6 address 2000::1::/64tunnel source loopback 1tunnel destina tion 2.2.2.2tunnel mode ipv6ipipv6 eigrp 1
Which of the following are true of both OSPFv2 and OSPFv3?（）
Router R1 has the following configuration. Assuming R1's F0/0 interface has a MAC address of 0200.0011.1111, what IPv6 addresses will R1 list for interface F0/0 in the output of the show ipv6 interface brief command?（）interface f0/0ipv6 address 2345:0:0:8::1/64
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?（）ipv6 router ospf 1ipv6 unicast- routinginterface f0/0ipv6 address 2000 ::1/64ipv6 ospf 1 area 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 ospf 1 area 0
Which of the following is the shortest valid abbreviation for FE80:0000:0000:0000:0010:0000:0000:0123?（）
Look at the following configuration below and select the statements that are true.（）RD2(config)#router ospf 100RD2(config - router)# distance 180 10.1.10.1 0.0.0.0 match - meRD2(config -router)#!RD2(config - router) #ip access - list standard match - meRD2(config - std - nacl)# permit host 172.16.0.0