A.detailed list of personnel assigned to each task within the plan
B.a Layer 2 spanning tree design topology
C.rollback guidelines
D.placing all unused access ports in VLAN 1 to proactively manage port security
E.enabling SNMP access to Cisco Discovery Protocol data for logging and forensic analysis
您可能感興趣的試卷
你可能感興趣的試題
A.detailed VLAN information
B.an incident response plan
C.results of testing the new network configuration
D.an existing hierarchical network topology
E.a security policy for your organization
You are tasked with designing a security solution for your network.
What information should be gathered prior to designing the solution？（）
A.a list of applications currently in use in the network
B.IP addressing design plans so that the network can be appropriately segmented to mitigate potential network threats
C.detailed security device specifications
D.results from pilot network testing
You are tasked with designing a security solution for your network.
What information should be gathered prior to designing the solution？（）
A.IP addressing design plans so that the network can be appropriately segmented to mitigate potential network threats
B.detailed security device specifications
C.results from pilot network testing
D.results from a network audit
You are tasked with designing a security solution for your network.
What information should be gathered prior to designing the solution？（）
A.IP addressing design plans so that the network can be appropriately segmented to mitigate potential network threats
B.a list of the customer requirements
C.detailed security device specifications
D.results from pilot network testing
Cat6500（config）# router ospf 1
Cat6500（config-router）# network 0.0.0.0 255.255.255.255 area 0
Cat6500（config-router）# nsf Cat6500（config-router）#end
Refer to the exhibit. The configuration is used to enable nonstop forwarding for OSPF on a Catalyst 6500 Series
Switch with redundant supervisor engines.
The default CEF configuration is unchanged. After testing， user traffic is interrupted and NSF is not operational.
What is the most likely reason？ （）
A.CEF was not properly configured.
B.OSPF was not properly configured for graceful restart.
C.Stateful switchover was not correctly configured.
D.NSF for OSPF is only supported in area 0.
最新試題
Refer to the exhibit. What does the command channel-group 1 mode desirable do？ （）
During routine maintenance， G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However， after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ？ （）
Which option correctly identifies the Cisco IOS switching methods in descending order from the fastest method to the slowest method？（）
How are STP timers and state transitions affected when a topology change occurs in an STP environment？（）
Refer to the exhibit. LACP has been configured on Switch1 as shown. Which is the correct command set to configure LACP on Switch2？（）
Refer to the exhibit. For what purpose is the command show ip cef used？（）
What will occur when a nonedge switch port that is configured for Rapid Spanning Tree does not receive a BPDU from its neighbor for three consecutive hello time intervals？（）
Which statement is correct about the use of the virtual interface on a WLC ？（）
What is the configured priority value of the Vlan105’s group on DS2 ？（）
Refer to the exhibit and the partial configuration of switch SW_A and SW_B. STP is configured on all switches in the network. SW_B receives this error message on the console port：00：06：34： %CDP-4-DUPLEX_MISMATCH： duplex mismatch discovered on FastEthernet0/5 （not half duplex）， with SW_A FastEthernet0/4 （half duplex） ， with TBA05071417（Cat6K-B） 0/4 （half duplex）. What would be the possible outcome of the problem？（）