A new floor has been added to the enterprise campus network， providing client access for desktop PCs， laptops， and IP phones for employees and guests. During verification， a few desktop PCs have limited corporate access but not Internet access. Most other desktop PCs， all laptops， and IP phones are working correctly. Additional information indicates that the desktop PCs are obtaining IP host addresses from the DHCP server， which is intended for only the IP phones.
Where should troubleshooting about this connectivity issue be focused？（）
A.DNS
B.first-hop redundancy protocol
C.DHCP server and options
D.VLAN mapping
E.client network configuration
F.routing protocols
您可能感興趣的試卷
你可能感興趣的試題
A new building has been added to the enterprise campus network， providing client access for desktop PCs， laptops， and IP phones for employees and guests. During verification， only a few laptops using
wireless are reported to have problems， while other desktops， IP phones， and most other wireless laptops are fully operational. Additional information received about the problem indicates that， while the problematic wireless laptops cannot reach internal corporate websites， they can reach the Internet.
Where should troubleshooting about this connectivity issue be focused？（）
A.client network configuration
B.VLAN mapping
C.routing protocols
D.first-hop redundancy protocol
You work as a network engineer for. You study the exhibit carefully. You have configured an interface to be an SVI for Layer 3 routing capabilities. Assuming that all VLANs have been correctly configured and based on the configuration example shown，
what can be determined？ （）
Exhibit：
A.Interface gigabitethernet0/2 will be excluded from Layer 2 switching and enabled for Layer 3 routing.
B.The interface is missing IP configuration parameters； therefore， it will only function at Layer 2.
C.The command switchport autostate exclude should be entered in global configuration mode， not sub-interface mode， to enable a Layer 2 port to be configured for Layer 3 routing.
D.The configured port is excluded in the calculation of the status of the SVI.
You have configured a Cisco Catalyst switch to perform Layer 3 routing via an SVI and have
assigned that interface to VLAN 20. To check the status of the SVI， you issue the show interfaces vlan 20 command at the CLI prompt. You see from the output display that the interface is in an "up/up" state.
What must be true in an SVI configuration to bring the VLAN and line protocol up？（）
A.The port must be physically connected to another Layer 3 device.
B.At least one port in VLAN 20 must be active.
C.The Layer 3 routing protocol must be operational and receiving routing updates from neighboring peer devices.
D.Because this is a virtual interface， the operational status will always be in an "up/up" state.
A.The best match of the ACL entries will be used for granularity of control.
B.They use source IP information for matching operations.
C.They use source and destination IP information for matching operations.
D.They use source IP information along with protocol-type information for finer granularity of control.
A.Enable the switch to participate in routing updates from external devices with the router command in global configuration mode.
B.Enter the no switchport command to disable Layer 2 functionality at the interface level.
C.Each port participating in routing of Layer 3 packets must have an IP routing protocol assigned on aperinterface level.
D.Routing is enabled by default on a multilayer switch， so the port can become a Layer 3 routing interface by assigning the appropriate IP address and subnet information.
最新試題
Which statement is correct about RSTP port roles？（）
How are STP timers and state transitions affected when a topology change occurs in an STP environment？（）
Refer to the exhibit. What command was issued on the Layer 3 switch Sw1 between Exhibit #1 and Exhibit #2？（）
Refer to the exhibit. Which statement is true about the output？（）
Refer to the exhibit. For what purpose is the command show ip cef used？（）
During routine maintenance， G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However， after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ？ （）
If G1/0/1 on DS1 is shutdown， what will be the current priority value of the Vlan105’s group on DS1 ？（）
Refer to the exhibit. Which Virtual Router Redundancy Protocol （VRRP） statement is true about the roles of the master virtual router and the backup virtual router？（）
Based on the show spanning-tree vlan 200 output shown in the exhibit， which two statements about the STP process for VLAN 200 are true？ （）
Refer to the exhibit. Switch S2 contains the default configuration. Switches S1 and S3 both have had the command spanning-tree mode rapid-pvst issued on them. What will be the result？（）