You work as a network engineer for. You study the exhibit carefully. Based on the output of the show command，
what can you determine regarding EIGRP routing being performed by the switch？ （）
Exhibit：
A.There are 20 neighbors in the EIGRP neigbor table.
B.EIGRP is running normally and receiving IPv4 routing updates.
C.The switch has not established any neighbor relationships. Further network testing and troubleshooting must be performed to determine the cause of the problem.
D.EIGRP status cannot be determined. The command show ip eigrp topology would determine the routing protocol status.
您可能感興趣的試卷
你可能感興趣的試題
You work as a network engineer for . You study the exhibit carefully. Based upon the output shown，
what can you determine？（）
Exhibit：
A.VLAN 30 is not operational due to the fact that there are no packet or byte counts indicated.
B.The IP Cisco Express Forwarding configuration is capable of supporting IPv6.
C.Cisco Express Forwarding load balancing has been disabled.
D.SVI VLAN 30 connects directly to the 10.1.30.0/24 network due to a valid glean adjacency.
You work as a network engineer for. You study the exhibit carefully. Based on the configuration
shown，
which two statements are correct regarding this Layer 3 security configuration example？ （）
Exhibit：
A.Source IP and MAC filtering on VLANs 10 and 11 will occur.
B.The switch will drop the configured MAC and IP address source bindings and forward all other traffic.
C.DHCP snooping will be automatically enabled on the access VLANs.
D.IP Source Guard is enabled.
E.Static IP source binding can only be configured on a routed port.
You work as a network engineer for. You study the exhibit carefully. From the configuration sample shown of a Cisco Catalyst 3560 Series Switch，
what can you determine regarding Layer 3 routing functionality of the interface？（）
Exhibit：
A.The interface is configured correctly for Layer 3 routing capabilities.
B.The interface needs an additional configuration entry to enable IP routing protocols.
C.The interface subcommand ip routing is required to enable IP routing on the interface.
D.An SVI interface is required to enable IP routing for network 192.20.135.0.
A new floor has been added to the enterprise campus network， providing client access for desktop PCs， laptops， and IP phones for employees and guests. During verification， a few desktop PCs have limited corporate access but not Internet access. Most other desktop PCs， all laptops， and IP phones are working correctly. Additional information indicates that the desktop PCs are obtaining IP host addresses from the DHCP server， which is intended for only the IP phones.
Where should troubleshooting about this connectivity issue be focused？（）
A.DNS
B.first-hop redundancy protocol
C.DHCP server and options
D.VLAN mapping
E.client network configuration
F.routing protocols
A new building has been added to the enterprise campus network， providing client access for desktop PCs， laptops， and IP phones for employees and guests. During verification， only a few laptops using
wireless are reported to have problems， while other desktops， IP phones， and most other wireless laptops are fully operational. Additional information received about the problem indicates that， while the problematic wireless laptops cannot reach internal corporate websites， they can reach the Internet.
Where should troubleshooting about this connectivity issue be focused？（）
A.client network configuration
B.VLAN mapping
C.routing protocols
D.first-hop redundancy protocol
最新試題
How are STP timers and state transitions affected when a topology change occurs in an STP environment？（）
Which option correctly identifies the Cisco IOS switching methods in descending order from the fastest method to the slowest method？（）
Refer to the exhibit. LACP has been configured on Switch1 as shown. Which is the correct command set to configure LACP on Switch2？（）
Which two statements about the various implementations of STP are true？（）
Refer to the exhibit. What will happen when one more user is connected to interface FastEthernet 5/1？ （）
DS2 has not become the active device for Vlan103’s HSRP group even though all interfaces are active. As related to Vlan103’s HSRP group. What can be done to make the group function properly ？ （）
Which statement is correct about the use of the virtual interface on a WLC ？（）
Refer to the exhibit. Switch 15 is configured as the root switch for VLAN 10 but not for VLAN 20. If the STP configuration is correct， what will be true about Switch 15？（）
Which two statements are true about BPDU port-guard and BPDU filtering？（）
Based on the show spanning-tree vlan 200 output shown in the exhibit， which two statements about the STP process for VLAN 200 are true？ （）