On an Aironet card， LED 0 and LED 1 are blinking alternately.
What does this indicate？ （）
A.The Aironet card is in power save mode.
B.The Aironet card is looking for a network association.
C.The Aironet card is joined to a network， but there is no network activity.
D.The Aironet card is joined to a network， and there is network activity.
您可能感興趣的試卷
你可能感興趣的試題
A.Static secure MAC addresses can be configured in conjunction with voice VLANs.
B.PortFast is automatically enabled when voice VLANs are configured.
C.PortFast must be manually configured when voice VLANs are configured.
D.Voice VLANs are typically configured on uplink ports.
E.Voice VLANs are typically configured on access ports.
Refer to the exhibit.
Which statement is true about the display of the command show pagp 1 neighbor command？（）
A.STP packets are sent out the Gi0/1 interface only.
B.STP packets are sent out both the Gi0/1 and Gi0/2 interfaces.
C.CDP packets are sent out the Gi0/1 interface only.
D.CDP packets are sent out the Gi0/2 interface only.
A.allows an UDLD port to automatically reset when it has been shutdown
B.resets all UDLD enabled ports that have been shutdown
C.removes all UDLD configurations from interfaces that were globally enabled
D.removes all UDLD configurations from interfaces that were enabled per-port
Refer to the exhibit. When a profile is configured in the Aironet Desktop Utility，
which security option permits the configuration of host-based Extensible Authentication Protocol （EAP）？（）
A.WPA/WPA2/CCKM
B.WPA/WPA2 Passphrase
C.802.1x
D.Pre-Shared Key （Static WEP）
Network topology exhibit：
Interface VLAN 101 exhibit：
Interface VLAN 102 exhibit：
Interface VLAN 104 exhibit：
Interface VLAN 105 exhibit：
You work as a network technician at. You study the network topology and the other exhibits carefully. Consider the distribution switches 1 and 2. 1 is the primary device for Vlan 101， 102， 105. 2 is the primary device for Vlan 103 and 104
Note： Please refer to the #2 scenario.
During routine maintenance， it became necessary to shutdown G1/0/1 on1 and2.
All other interface were up. During this time，1 became the active device for Vlan104’s HSRP group. As related to Vlan104’s HSRP group.
What can be done to make the group function properly ？（）
A.On 1， disable preempt
B.On 2， decrease the priority value to a value less than 150
C.On 1， increase the decrement value in the track command to a value greater than 6
D.On 1， disable track command.
最新試題
Which two statements are true about BPDU port-guard and BPDU filtering？（）
Refer to the exhibit. On the basis of the output of the show spanning-tree inconsistentports command， which statement about interfaces FastEthernet 0/1 and FastEthernet 0/2 is true？（）
During routine maintenance， G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However， after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ？ （）
Refer to the exhibit. Based on the output of the show spanning-tree command， which statement is true？ （）
Refer to the exhibit. What command was issued on the Layer 3 switch Sw1 between Exhibit #1 and Exhibit #2？（）
Refer to the exhibit. Which statement is true about the output？（）
Which option correctly identifies the Cisco IOS switching methods in descending order from the fastest method to the slowest method？（）
Refer to the exhibit. For what purpose is the command show ip cef used？（）
What must be the same to make multiple switches part of the same Multiple Spanning Tree （MST）？（）
Based on the show spanning-tree vlan 200 output shown in the exhibit， which two statements about the STP process for VLAN 200 are true？ （）