Each of these vlans has one host each on its port SVI on vlan 1 - ip 192.168.1.11 with snm Switch B -
Ports 3， 4 connected to ports 3 and 4 on Switch A
Port 15 connected to Port on Router.
Tasks to do
1. Use non proprietary mode of aggregation with Switch B being the initiator -- Assumed use LACP with B being in Active mode
2. Use non proprietary trunking and no negotiation -- Assumed use switchport mode trunk and switchport trunk encapsulation dot1q
3. Restrict only to vlans needed
-- Assumed either vtp pruning or allowed vlan list. vtp pruning command did not seem to work on the simulator so landed using allowed vlan list
4. SVI on vlan 1 with some ip and subnet given
5. Configure switch A so that nodes other side of Router C are accessible -- Assumed this to mean that on switch A default gatway has to be configured.
6. Make switch B the root
-- Could not get this to work. Exam hung when I tried the command spanning-tree vlan 1，21-23 priority 4096
您可能感興趣的試卷
你可能感興趣的試題
Configure the Multilayer Switch so that PCs from VLAN 2 and VLAN 3 can communicate with the Server.
A.TCP retransmits
B.benign
C.greedy
D.drop sensitive
E.smooth
F.delay insensitive
Refer to the exhibit. The command spanning-tree guard root is configured on interface Gi0/0 on both switch S2 and S5. The global configuration command spanning-tree uplinkfast has been configured on both switch S2 and S5. The link between switch S4 and S5 fails.
Will Host A be able to reach Host B？ （）
A.Yes. Traffic can pass either from switch S6 to S3 to S2 to S1， or， from switch S6 to S5 to S2 to S1.
B.No. Traffic will pass from switch S6 to S5 and dead-end at interface Gi 0/0.
C.No. Traffic will loop back and forth between switch S5 and S2.
D.Yes. Traffic will pass from switch S6 to S3 to S2 to S1.
E.No. Traffic will either pass from switch S6 to S5 and dead-end， or traffic will pass from switch S6 to S3 to S2 and dead-end.
On an Aironet card， LED 0 and LED 1 are blinking alternately.
What does this indicate？ （）
A.The Aironet card is in power save mode.
B.The Aironet card is looking for a network association.
C.The Aironet card is joined to a network， but there is no network activity.
D.The Aironet card is joined to a network， and there is network activity.
A.Static secure MAC addresses can be configured in conjunction with voice VLANs.
B.PortFast is automatically enabled when voice VLANs are configured.
C.PortFast must be manually configured when voice VLANs are configured.
D.Voice VLANs are typically configured on uplink ports.
E.Voice VLANs are typically configured on access ports.
最新試題
Refer to the exhibit. Based on the output of the show spanning-tree command， which statement is true？ （）
Which two statements are true about BPDU port-guard and BPDU filtering？（）
Which router redundancy protocol cannot be configured for interface tracking？（）
Refer to the exhibit. The command switchport mode access is issued on interface FastEthernet0/13 on switch CAT1. What will be the result？（）
During routine maintenance， G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However， after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ？ （）
Which statement is correct about the use of the virtual interface on a WLC ？（）
Refer to the exhibit. What command was issued on the Layer 3 switch Sw1 between Exhibit #1 and Exhibit #2？（）
Which three statements about STP timers are true？（）
Based on the show spanning-tree vlan 200 output shown in the exhibit， which two statements about the STP process for VLAN 200 are true？ （）
Refer to the exhibit and the partial configuration of switch SW_A and SW_B. STP is configured on all switches in the network. SW_B receives this error message on the console port：00：06：34： %CDP-4-DUPLEX_MISMATCH： duplex mismatch discovered on FastEthernet0/5 （not half duplex）， with SW_A FastEthernet0/4 （half duplex） ， with TBA05071417（Cat6K-B） 0/4 （half duplex）. What would be the possible outcome of the problem？（）