A. all interfaces in the path toward the destination
B. all networks in the path toward the destination
C. adjacent next hop router in the path toward the destination
D. all routers in the path toward the destination
E. all interfaces through which the packets can be routed
F. type of service and precedence in the IP packets
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit. The routing protocols EIGRP and OSPF have been configured as indicated in the exhibit. Given the partial configuration of router R2, which network will be present in th e routing table of R4?()
A. Network B
B. Network A and Network B
C. Network A
D. neither Network A nor Network B
A. L1 ES
B. L2 IS
C. L2 ES
D. L1 IS
E. L1/L2 IS
A. IS - IS is more CPU - intensive than is OSPF
B. For greater fine tuning there are more IS - IS timers
C. IS - IS LSP con tains TLV fields and OSPF LSU contains the LSAs
D. New additions to the protocol are easily implemented in OSPF but not with IS - IS
E. OSPF has more area types than does IS - IS
A. uses a default IOS metric of 10 on each interface
B. uses an on - demand circuit to reduce the hello and LSA flooding across switched WAN li nks,such as ISDN
C. uses a DIS and a backup DIS to present the psuedo - node on the LAN
D. encapsulates PDUs directly into a data - link frame
E. uses stubby areas to improve network scalability
F. runs PRC (Partial Route Calculations) to calculate IP re achability information
A. BGP requires redundant TCP sessions between iBGP peers.
B. Routes learned via eBGP are never propagated to other iBGP peers.
C. A full mesh allows for optimal routing within the Transit AS.
D. Routes learned via iBGP are never propagated to other eBGP peers.
E. Routes learned via iBGP are never propagated t o other iBGP peers.
最新試題
Which of the following features work the same in both RIP- 2 and RIPng?()
The answers each list a tunnel method and two consecutive IPv6 address quartets.Which answers identify a tunneling method that relies on an IPv4 address to be embedded into an IPv6 address, within the correct quartets listed?()
Router R1 connects to Router R2 over an Ethernet LAN with both routers using their F0/0 interfaces. R1 learns a route from R2 using EIGRP f or IPv6. That route lists F0/0 as the outgoing interface with R2 as the next hop. The configuration excerpt shows all relevant configuration on R2's F0/0 interface. Which of the following is true about R1's route?()interface f0/0mac - address 1111.1111.1 111ipv6 address 2000::/64 eui - 64ipv6 address 2001::1/64
Router R1 use s MAC address 1111.1111.1111 for its Fa0/0 interface. An engineer sees the following configuration in the output of a show running - config command. Then, the engineer issues a show ipv6 interface brief command. What global unicast IPv6 address does this c ommand display for interface tunnel 1?()interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 1tunnel source loopback 1tunnel destination 192.168.1.2tunnel mode ipv6ip isatapipv6 address 2000::/64 eui - 64
Which of the following answers lists either a protocol or function that can be used by a host to dynamically learn its own IPv6 address?()
Router R1 has been conf igured with an ipv6 route 2000::/64 S0/0/0 64 command.Which of the following does the 64 at the end of the command represent?()
The following configuration exists on a router on one end of an IPv6 tunnel. Although the configuration added so far is correct, the configuration is incomplete. Which type of tunnel is most likely to be intended by the network engineer?()interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 2ipv6 address 2002:C0A8:10 1::1/64tunnel source loopback 1
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exis ts in a planning document intended to be used to copy/paste into Router R1 to enable EIGRP for IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about EIGRP for IPv6 on R1 after this configuration has been pasted into R1?()ipv6 router eigrp 1ipv6 unicast- routinginterface f0/0ipv6 address 2000::1/64ipv6 eigrp 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 eigrp 1
The following output on Router R1 lists details of a BGP route for 190.1.0.0/16. Which of the following is true based on this output?()R1# show ip bgp 19 0.1.0.0/16BGP routing table entry for 190.1.0.0/16, version 121Paths: (1 available, best #1, table Default - IP - Routing - Table)Advertised to update - groups:11 2 3 41.1.1.1 from 2.2.2.2 (3.3.3.3)Origin IGP, metric 0, localpref 100, valid, internal, best
Look at the following configuration below and select the statements that are true.()RD2(config)#router ospf 100RD2(config - router)# distance 180 10.1.10.1 0.0.0.0 match - meRD2(config -router)#!RD2(config - router) #ip access - list standard match - meRD2(config - std - nacl)# permit host 172.16.0.0