A network design shows that R1 has four different possible paths from itself to the Data Center subnets.
Which one of the following commands is most likely to show you all the possible next - hop IP addresses for these four possible routes?（）
A. show ip eigrp topology
B. show ip eigrp topology all - links
C. show ip route eigrp
D. show ip route eigrp all - links
E. show ip eigrp topology all - learned
您可能感興趣的試卷
你可能感興趣的試題
A company has a Frame Relay WAN with one central - site router and 100 branch office routers. A partial mesh of PVCs exists: one PVC between the central site and each of the 100 branch routers.
Which of the following could be true about the number of EIGRP neighbor ships?（）
A. A partial mesh totaling 100: one between the central - site router and each of the 100 branches.
B. A full mesh - (101 * 100) / 2 = 5050 - One neighborship between each pair of routers.
C. 101 - One between each router (including the central site) a nd its nearby PE router.
D. None of the answers is correct.
Refer to the exhibit. Which two statements are true about the partial configuration that is shown? （）
A. The first DHCP client to connect to the FastEthernet 0/1 interface will receive the IP address 10.10.0.1.
B. DHCP requests received on the FastEthernet 0/1 interface will be forwarded to 10.0.0.2.
C. The first DHCP client to connect to the FastEthernet 0/0 interface will receive the IP a ddress 10.0.0.1
D. The first DHCP client to connect to the FastEthernet 0/0 interface will receive the IP address 10.0.0.6.
E. Hosts connected to the FastEthernet0/1 interface will not receive DHCP replies from the router.
A. BOOTP
B. TFTP
C. ARP
D. DNS
E. proxy - ARP
F. FTP
Refer to the exhibit. Routers R1 and R2 have established a neighbor relationship and are exchanging routing information. The network design requires that R1 r eceive routing updates from R2, but not advertise any routes to R2. Which configuration command sequence will successfully accomplish this task? （）
A. R1(config)# router eigrp 1 R1(config - router)# passive - interface serial 0
B. R1(config)# access - list 2 0 deny any R1(config)# router eigrp 1 R1(config - router)# distribute - list 20 out serial 0
C. R2(config)# access - list 20 permit any R2(config)# router eigrp 1 R2(config - router)# distribute - list 20 in serial 0
D. R1(config)# access - list 20 permit any R 1(config)# router eigrp 1 R1(config - router)# distribute - list 20 in serial 0
E. R2(config)# access - list 20 deny any R2(config)# router eigrp 1 R2(config - router)# distribute - list 20 out serial 0
F. R2(config)# router eigrp 1 R2(config - router)# passive - interface serial 0
A. all interfaces in the path toward the destination
B. all networks in the path toward the destination
C. adjacent next hop router in the path toward the destination
D. all routers in the path toward the destination
E. all interfaces through which the packets can be routed
F. type of service and precedence in the IP packets
最新試題
An engineer is reviewing another engineer's sample configuration for a GRE tunnel used to pass IPv6 traffiC. The tunnel ha s not yet been configured on the router.Which of the following commands is not required for the configuration to pass IPv6 traffic?（）
Which of the following IPv6 tunneling mechanisms support IPv6 IGP routing protocols?（）
Router R1 use s MAC address 1111.1111.1111 for its Fa0/0 interface. An engineer sees the following configuration in the output of a show running - config command. Then, the engineer issues a show ipv6 interface brief command. What global unicast IPv6 address does this c ommand display for interface tunnel 1?（）interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 1tunnel source loopback 1tunnel destination 192.168.1.2tunnel mode ipv6ip isatapipv6 address 2000::/64 eui - 64
Router R1 lists the following output from a show command. Which of the following is true about R1?（）R1# show ip v6 interface f0/0FastEthernet0/0 is up, line protocol is upIPv6 is enabled, link - local address is FE80::213:19FF:FE12:3456No Virtual link - local address(es):Global unicast address(es):2000::4:213:19FF:FE12:3456, subnet is 2000:0:0:4::/64 [EUI]Jo ined group address(es):FF02::1FF02::2FF02::1:FF:12:3456
Which of the following answers lists either a protocol or function that can be used by a host to dynamically learn its own IPv6 address?（）
Router R1 has been conf igured with an ipv6 route 2000::/64 S0/0/0 64 command.Which of the following does the 64 at the end of the command represent?（）
Router R1 has the following configuration. Assuming R1's F0/0 interface has a MAC address of 0200.0011.1111, what IPv6 addresses will R1 list for interface F0/0 in the output of the show ipv6 interface brief command?（）interface f0/0ipv6 address 2345:0:0:8::1/64
An enterprise has plans to start adding IPv6 support. The initial deployment requires support from some IPv6 - only device s that need to access servers that support only IPv4.Which of the following tools would be most appropriate?（）
A client host uses IPv4 to communicate with one ser ver and IPv6 to communicate with another.Which of the following IPv6 coexistence features is likely at work on the host?（）
Which of the following is helpful to allow an IPv6 host to learn the IP address of a default gateway on its subnet?（）