A.The BID is made up of the bridge priority value（two bytes） and bridge MAC address （six bytes）.
B.The BID is made up of the bridge priority （four bits）， the system ID （12 bits）， and a bridge MAC address （48 bits）.
C.The BID is made up of the system ID （six bytes） and bridge priority value （two bytes）.
D.The system ID value is the VLAN ID （VID）.
E.The system ID value is a unique MAC address allocated from a pool of MAC addresses assigned to the switch or module.
F.The system ID value is a hex number used to measure the preference of a bridge in the spanning-tree algorithm.
您可能感興趣的試卷
你可能感興趣的試題
Based on the show spanning-tree vlan 200 output shown in the exhibit，
which two statements about the STP process for VLAN 200 are true？ （）
A.BPDUs will be sent out every two seconds.
B.The time spent in the listening state will be 30 seconds.
C.The time spent in the learning state will be 15 seconds.
D.The maximum length of time that the BPDU information will be saved is 30 seconds.
E.This switch is the root bridge for VLAN 200.
F.BPDUs will be sent out every 10 seconds.
A.HSRP
B.GLBP
C.VRRP
D.SLB
E.RPR
F.RPR+
A.STP timers values （hello， forward delay， max age） are included in each BPDU.
B.A switch is not concerned about its local configuration of the STP timers values. It will only consider the value of the STP timers contained in the BPDU it is receiving.
C.To successfully exchange BPDUs between two switches， their STP timers value （hello， forward delay， max age） must be the same.
D.If any STP timer value （hello， forward delay， max age） needs to be changed， it should at least be changed on the root bridge and backup root bridge.
E.On a switched network with a small network diameter， the STP hello timer can be tuned to a lower value to decrease the load on the switch CPU.
F.The root bridge passes the timer information in BPDUs to all routers in the Layer 3 configuration.
Examine the diagram. A network administrator has recently installed the above switched network using 3550s and would like to control the selection of the root bridge.
Which switch should theadministrator configure as the root bridge and which configuration command must theadministrator enter to accomplish this？（）
A.DSW11（config）# spanning-tree vlan 1 priority 4096
B.DSW12（config）# set spanning-tree priority 4096
C.ASW13（config）# spanning-tree vlan 1 priority 4096
D.DSW11（config）# set spanning-tree priority 4096
E.DSW12（config）# spanning-tree vlan 1 priority 4096
F.ASW13（config）# set spanning-tree priority 4096
Given the above diagram and assuming that STP is enabled on all switch devices，
which two statements are true？（）
A.DSW11 will be elected the root bridge.
B.DSW12 will be elected the root bridge.
C.ASW13 will be elected the root bridge.
D.P3/1 will be elected the nondesignated port.
E.P2/2 will be elected the nondesignated port.
F.P3/2 will be elected the nondesignated port.
最新試題
What will occur when a nonedge switch port that is configured for Rapid Spanning Tree does not receive a BPDU from its neighbor for three consecutive hello time intervals？（）
Which two statements about the various implementations of STP are true？（）
Refer to the exhibit. Switch S2 contains the default configuration. Switches S1 and S3 both have had the command spanning-tree mode rapid-pvst issued on them. What will be the result？（）
What two things will occur when an edge port receives a BPDU？（）
Refer to the exhibit and the partial configuration of switch SW_A and SW_B. STP is configured on all switches in the network. SW_B receives this error message on the console port：00：06：34： %CDP-4-DUPLEX_MISMATCH： duplex mismatch discovered on FastEthernet0/5 （not half duplex）， with SW_A FastEthernet0/4 （half duplex） ， with TBA05071417（Cat6K-B） 0/4 （half duplex）. What would be the possible outcome of the problem？（）
Which router redundancy protocol cannot be configured for interface tracking？（）
During routine maintenance， G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However， after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ？ （）
Refer to the exhibit. Which statement is true about the output？（）
Which option correctly identifies the Cisco IOS switching methods in descending order from the fastest method to the slowest method？（）
Refer to the exhibit. For what purpose is the command show ip cef used？（）