R1 is internal to area 1, and R2 is internal to area 2. Subnet 10.1.1.0/24 exists in area 2 as a connected subnet off R2. ABR ABR1 connects area 1 to backbone area 0, and ABR2 c onnects area 0 to area 2.
Which of the following LSAs must R1 use when calculating R1's best route for 10.1.1.0/24?（）
A. R2's Type 1 LSA
B. Subnet 10.1.1.0/24's Type 2 LSA
C. ABR1's Type 1 LSA in area 0
D. Subnet 10.1.1.0/24's Type 3 LSA in Area 0
E. Subnet 10.1.1.0/24's Type 3 LSA in Area 1
您可能感興趣的試卷
你可能感興趣的試題
Routers R1, R2, R3, and R4 connect to the same 10.10.10.0/24 LAN- based subnet. OSPF is fully working in the subnet. Later, R5, whose OSPF priority is higher than the other four routers, joins the subnet.
Which of the following are true about the OSPF database exchange process over this subnet at this point?（）
A. R5 will send its DD, LSR, and LSU packets to the 224.0.0.5 all - DR - routers multicast address.
B. R5 will send its DD, LSR, and LSU pack ets to the 224.0.0.6 all - DR - routers multicast address.
C. The DR will inform R5 about LSAs by sending its DD, LSR, and LSU packets to the 224.0.0.6 all- SPF - routers multicast address.
D. The DR will inform R5 about LSAs by sending its DD, LSR, and LSU pa ckets to the 224.0.0.5 all- SPF - routers multicast address.
A. LSR
B. LSAck
C. LSU
D. DD
E. Hello
A verification plan shows a network diagram with branch office Routers B1 through B100, plus two ABRs, ABR1, and ABR2, all in area 100. The branches connect to the ABRs using Frame Relay point - to - point subinterfaces. The verification plan lists the output of the show i p ospf database summary 10.100.0.0 command on a router B1, one of the branches.
Which of the following is true regarding the output that could be listed for this command?（）
A. The output lists nothing unless 10.100.0.0 has been configured as a summary rou te using the area range command.
B. If 10.100.0.0 is a subnet in area 0, the output lists one Type 3 LSA, specifically the LSA with the lower metric when comparing ABR1's and ABR2's LSA for 10.100.0.0.
C. If 10.100.0.0 is a subnet in area 0, the output lists two Type 3 LSAs, one each created by BR1 and ABR2.
D. None, because the Type 3 LSAs would exist only in the ABR's LSDBs.
A network planning diagram shows a large internetwork with many routers. The configurations show that OSPF has been enabled on all interfaces, I P addresses correctly configured, and OSPF workinG.
For which of the following cases would you expect a router to create and flood a Type 2 LSA?（）
A. When OSPF is enabled on a LAN interface, and the router is the only router connected to the subnet.
B. When OSPF is enabled on a point - to -point serial link, and that router has both the higher router ID and higher interface IP address on the link.
C. When OSPF is enabled on a Frame Relay point - to - point subinterface, has the lower RID and lower subinterfa ce IP address, and otherwise uses default OSPF configuration on the interface.
D. When OSPF is enabled on a working LAN interface on a router, and the router has been elected BDR.
E. None of the other answers is correct.
A network de sign shows area 1 with three internal routers, area 0 with four internal routers, and area 2 with five internal routers. Additionally, one ABR (ABR1) connects areas 0 and 1, plus a different ABR (ABR2) connects areas 0 and 2.
How many Type 1 LSAs would b e listed in ABR2's LSDB?（）
A. 6
B. 7
C. 15
D. 12
E. None of the other answers is correct.
最新試題
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exis ts in a planning document intended to be used to copy/paste into Router R1 to enable EIGRP for IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about EIGRP for IPv6 on R1 after this configuration has been pasted into R1?（）ipv6 router eigrp 1ipv6 unicast- routinginterface f0/0ipv6 address 2000::1/64ipv6 eigrp 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 eigrp 1
An enterprise has plans to start adding IPv6 support. The initial deployment requires support from some IPv6 - only device s that need to access servers that support only IPv4.Which of the following tools would be most appropriate?（）
A client host uses IPv4 to communicate with one ser ver and IPv6 to communicate with another.Which of the following IPv6 coexistence features is likely at work on the host?（）
Which of the following features work the same in both RIP- 2 and RIPng?（）
Which of the following is helpful to allow an IPv6 host to learn the IP address of a default gateway on its subnet?（）
Which of the following is the shortest valid abbreviation for FE80:0000:0000:0000:0010:0000:0000:0123?（）
Router R1, a branch router, connects to the Internet using DSL. Some traffic flows through a GRE and IPsec tunnel, over the DSL connection, destined for an Enterprise network.Which of the following answers best describes the router's logic that tells the router, for a given packet, to apply GRE encapsulation to the packet?（）
The following output occurs on Router R1 , which runs both EIGRP for IPv6 and OSPFv3, with redistribution from EIGRP into OSPF configured with the redistribute eigrp 1 metric 25 command. Interface S0/0/1 has been enabled for EIGRP ASN 1. Which of the following should be true of redistribution in this case?（）D 2000::/64 [90/1422516]via FE80::213:19FF:FE7B:5026, Serial0/0/1C 2000:0:0:1::/64 [0/0]via Serial0/0/1, directly connectedL 2000::1:213:19FF:FE7B:5004/128 [0/0]via Serial0/0/1, receive
The following output on Router R1 lists details of a BGP route for 190.1.0.0/16. Which of the following is true based on this output?（）R1# show ip bgp 19 0.1.0.0/16BGP routing table entry for 190.1.0.0/16, version 121Paths: (1 available, best #1, table Default - IP - Routing - Table)Advertised to update - groups:11 2 3 41.1.1.1 from 2.2.2.2 (3.3.3.3)Origin IGP, metric 0, localpref 100, valid, internal, best
Router R1 has been conf igured with an ipv6 route 2000::/64 S0/0/0 64 command.Which of the following does the 64 at the end of the command represent?（）