Router R1 learns two routes with BGP for prefix 200.1.0.0/16. Comparing the two routes, route 1 has a longer AS_Path Length, bigger MED, bigger Weight, and smaller Loca l PreferencE.
Which of the following is true about Router R1's choice of best path for this prefix?（）
A. Route 1 is the best route.
B. Route 2 is the best route.
C. The routes tie as best, but one will be picked to be placed in the routing table based on tiebreakers.
D. Neither route is considered best.
您可能感興趣的試卷
你可能感興趣的試題
An engineer is preparing an implementation plan in which the configuration needs to influence BGP's choice of best path.
Which of the following is least likely to be used by the configuration in this imple mentation plan?（）
A. Weight
B. Origin code
C. AS_Path
D. Local_Pref
A. clear ip bgp *
B. clear ip bgp 1.1.1.1
C. clear ip bgp * soft
D. clear ip bgp 1.1.1.1 out
A. A neighbor distribute - list out command, referencing a standard ACL
B. A neighbor prefix - list out command
C. A neighbor filter - list out command
D. A neighbor distribute - list out command, referencing an extended ACL
E. A neighbor route - map out command
R1 is currently advertising prefixes 1.0.0.0/8, 2.0.0.0/8, and 3.0.0.0/8 over its eBGP connection to neighbor 2.2.2.2 (R2). An engineer configures a prefix list (fred) on R1 that permits only 2.0.0.0/8 and then enables the filter with the neighbor R2 prefix- list fred out command. Upon exiting configuration mode, the engineer uses some show commands on R1, but no other commands.
Which of the following is true in this case?（）
A. The show ip bgp neighbor 2 .2.2.2 received -routes command lists the three original prefixes.
B. The show ip bgp neighbor 2.2.2.2 advertised - routes command lists the three original prefixes.
C. The show ip bgp neighbor 2.2.2.2 routes command lists the three original prefixes.
D. T he show ip bgp neighbor 2.2.2.2 routes command lists only 2.0.0.0/8.
E. The show ip bgp neighbor 2.2.2.2 advertised - routes command lists only 2.0.0.0/8.
A company uses Routers R1 and R2 to connect to ISP1 and ISP2, respectively, with Routers I1 and I2 used at th e ISPs. R1 peers with I1 and R2; R2 peers with I2 and R1. R1 and R2 do not share a common subnet, relying on other routers internal to the Enterprise for IP connectivity between the two routers.
Which of the following could be used to prevent potential routing loops in this design?（）
A. Using an iBGP mesh inside the Enterprise core
B. Configuring default routes in the Enterprise pointing to both R1 and R2
C. Redistributing BGP routes into the Enterprise IGP
D. Tunneling the packets for the i BGP connection between R1 and R2
最新試題
An Enterprise rou ter, Ent1, displays the following excerpt from the show ip bgp command. ENT1 has an eBGP connection to an ISP router with address 3.3.3.3 and an iBGP connection to a router with address 4.4.4.4. Which of the following is most likely to be true?（）Network Next Hop Metric LocPrf Weight Path*> 3.3.3.3 0 0 1 1 1 1 218 i
An engineer is trying to summarize the following networks using the "ip summary- address eigrp"command:10.8.88.0/2510.8.89.48/2910.8.64.96/27Which network and subnet mask below would be the smallest EIGRP summary address to include all three subnets?（）
Which of the following is helpful to allow an IPv6 host to learn the IP address of a default gateway on its subnet?（）
Router R1 has the following configuration. Assuming R1's F0/0 interface has a MAC address of 0200.0011.1111, what IPv6 addresses will R1 list for interface F0/0 in the output of the show ipv6 interface brief command?（）interface f0/0ipv6 address 2345:0:0:8::1/64
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable RIPng and IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Which of the following is true about RIPng on R1 after this configuration has been pasted into R1?（）ipv6 unicast- routinginterface f0/0ipv6 rip one enableipv6 address 2000::1/64interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 rip one enable
An enterprise has plans to start adding IPv6 support. The initial deployment requires support from some IPv6 - only device s that need to access servers that support only IPv4.Which of the following tools would be most appropriate?（）
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?（）ipv6 router ospf 1ipv6 unicast- routinginterface f0/0ipv6 address 2000 ::1/64ipv6 ospf 1 area 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 ospf 1 area 0
Look at the following configuration below and select the statements that are true.（）RD2(config)#router ospf 100RD2(config - router)# distance 180 10.1.10.1 0.0.0.0 match - meRD2(config -router)#!RD2(config - router) #ip access - list standard match - meRD2(config - std - nacl)# permit host 172.16.0.0
Router R1, a branch router, connects to the Internet using DSL. Some traffic flows through a GRE and IPsec tunnel, over the DSL connection, destined for an Enterprise network.Which of the following answers best describes the router's logic that tells the router, for a given packet, to apply GRE encapsulation to the packet?（）
Router R1, a branch router, connects to the Internet using DSL. The engineer plans to use a configuration with a dialer interface. The answers list a feature and interface on which the feature could be configured.Which combinations accurately describe the interface under which a feature will be configured?（）