When configuring a cisco 3845 integrated services router to support 802.11b and g clients.
Which of the following commands would be correct？（）
A.router（config-if）# speed basic-1.0 2.0 5.5 6.0 9.0 11.0 12.0 18.0 24.0 36.0 48.0 54.0
B.router（config-if）# speed 1.0 2.0 5.5 6.0 9.0 basic-11.0 12.0 basic-18.0 24.0 36.0 48.0 54.0
C.router（config-if）# speed basic-1.0 2.0 5.5 basic-6.0 9.0 11.0 12.0 18.0 24.0 36.0 48.0 54.0
D.router（config-if）# speed 1.0 2.0 5.5 basic-6.0 9.0 11.0 12.0 18.0 24.0 36.0 48.0 54.0
您可能感興趣的試卷
你可能感興趣的試題
A.enable concatenation on the non-root bridge only
B.enable concatenation on the root bridge only
C.enable concatenation on both the root bridge and non-root bridge
D.enable concatenation on the root bridge and set it as desirable on the non-root bridge
E.set concatenation as desirable on the root bridge and enable it on the non-root bridge
Eap-fast provides a secure tunnel during phase one to protect the user’s authentication credentials.
Which of these entities initializes the secure tunnel？（）
A.x.509 certificate
B.generic token card
C.pre shared key
D.protected access credential
Your customer has deployed a cisco wireless location appliance within its warehouse
environment. however，employees there have been experiencing problems when tracking objects using active rfid tags. the rfid beacon rate is 10 seconds and you have discovered an issue with the rfid timeout value.
Where and how should the rfid value be changed？（）
A.on the cisco wcs， to 95 seconds
B.on the wireless controller， to 45 seconds
C.on the wireless controller， to 95 seconds
D.on the cisco wcs， to 45 seconds
You are installing a cisco aironet 1000 series controller-based access point. when you boot it， all the leds on the access point blink together.
What does this indicate about the access point？（）
A.duplicate ip address
B.code upgrade in progress
C.normal operation
D.searching for primary controller
A.ipx
B.ip
C.udp
D.tcp
最新試題
When configuring a WLAN controller for a voice application using Cisco 7920 wireless IP phones，which two general control settings should you select？（）
Which protocol does the RADIUS server use inside the secure tunnel of EAP-FAST to authenticatethe client when one-time passwords are in use？（）
When configuring Cisco Secure ACS to support wireless EAP authentication， which device must be configured as a AAA client？（）
You are troubleshooting a problem with a Cisco 7920 wireless IP phone that is causing the phoneto drop calls. The problem appears to be roaming bandwidth issue. In order to verify what kind ofissue it is， you decide to increase the bandwidth reserve for roaming on the WLAN controller tomaximum.What level do you set the bandwidth to？（）
A Cisco Wireless Location Appliance has been added to track RFID tags placed on laptops beingused in a school.Classrooms at the school have concrete block walls. During testing，you discoverthat the accuracy of the system needs to be improved.You decide to edit the map in the Cisco WCS to add the interior walls.How many interior walls can you add to improve the accuracy of thelocation appliance？（）
You want to dynamically assign users to an 802.1Q VLAN as a result of their authentication. Inorder to accomplish this.Which two IETF RADIUS attributes should you configure on the CiscoSecure ACS？ （）
On a Cisco Aironet 802.11 a/b/g wireless LAN client adapter，the status LED and activity LED are alternating on and off.What does this indicate？（）
You have been called upon to add location-based services into an existing controller-basedwireless design which primarily encompasses handheld devices such as barcode scanners and Cisco7920 wireless IP phones.In which mode should you deploy the additional access points to achievethe density required without excessive co-channel interference？（）
Which of the following commands on the wireless interface of a Cisco 3845 Integrated Service Router allows the SSID to broadcast？（）
A Cisco WCS version 4.0 has been installed on a server with a dual Pentium 3.0 GHz processor，4GB RAM， and an 80 GB hard drive. A location appliance has been incorporated into the networkand is being monitored by the Cisco WCS. There are 3000 devices to be tracked but not all of themare being tracked on the Cisco WCS.What can be done to correct the problem？（）