A. CIS 1# show class-map forward Class map match-all forward ( id 3) Match ip dscp 18
B. CIS1#show access-map block Class map match-all block (id 4) Match ip dscp 43
C. CIS1# show class-map real-time Class map match-all block (id 5) Match ip dscp 16
D. CIS 1# show class-map pass Class map match-all real-time (id 2) Match ip dscp 40
您可能感興趣的試卷
你可能感興趣的試題
You are an experienced network administrator in an international company. During your working hours, customers complain that they experience intermittent data loss and they intermittently fail to connect to crucial servers. As shown in the following topology, the 802.1Q trunk between DSW111 and ASW1 fails. Though DSW112 is in the service of HSRP group 11, the SVI for VLAN 11 is up on DSW111.
So as to figure out the problem,
which three commands should you issue on DSW111? （）(Choose three.)
A. show standby vlan 11 brief
B. show interfaces vlan 11
C. show spanning-tree vlan 11
D. show interfaces
You are troubleshooting an issue which is causing full-sized packets entering the MPLS cloud be dropped. You have discovered that one of the switches in the MPLS core is not a Cisco switch, but otherwise the MPLS MTU size is set to 1508 bytes on the routers.
Based on this information, which of these may be the reason the packets are being dropped?（）
A. The switch on you MPLS core that was not produced by Cisco does not support oversized packets
B. No switches support oversized packets
C. By definition, the maximum MTU is 1500 bytes
D. As MPLS VPN labeling increases the size of the packet by 8 bytes, the IP MTU should have been changed to 1508
A. Layer 2 TTL
B. Layer 3 TTL
C. Layer 3 source address
D. Layer 3 destination address
A. Show module
B. Show errdisable detect
C. Show environment
D. Show diagnostic content
A Catalyst switch has just been installed and configured, and is not working as expected. You have decided to capture multiple show command outputs to study.
Which one command could you use that includes the output of many other show commands, such as show version and show running-config?（）
A. show configuration
B. show memory
C. show stacks
D. show tech-support
最新試題
Which three of these items are IPv6 transition mechanisms? （）(Choose three.)
In a high-availability network, which command, when placed on ports that have connected end stations, will allow you to prevent delays in service for end stations by placing a port in blocking mode?（）
Refer to the exhibit. Which two of these statements are correct? (Choose two.)（）
Which configuration will enable OSPF for IPv6 on FastEthernet 0/0/0?（）
Refer to the exhibit. Analyze the two traceroutes that are displayed. Which of these statements is correct in describing what most likely caused the traceroute differences?（）
What is the purpose of using VPN hardware acceleration equipment?（）
When a Cisco router is configured for SSH, it acts as an （）?
What are four advantages to using tunnel brokers in an IPv6 transition environment?（）
With a VPN Accelerator Module 2+ (VAM2+) installed in a Cisco 7200 series router, what will be the resulting action when entering the command no crypto engine accelerator slot number?（）
Refer to the exhibit. You want to minimize the downtime that results from supervisor engine switchovers on Cisco 6500 Series Switches and Cisco 7600 Series Routers. To achieve this, you are considering deploying a Cisco Nonstop Forwarding with Stateful Switchover solution using OSPF.In the exhibit you can see the output of the show ip ospf neighbor detail command.Which trait of systems using Cisco Nonstop Forwarding with Stateful Switchover and OSPF is shown in the exhibit output and will impact your plan?（）