On a standalone access point， client association using EAP-Cisco Wireless （Cisco-LEAP） isfailing， but association using EAP-PEAP is functioning.
What needs to be enabled on the standalone accesspoint to correct this issue？（）
A.network EAP
B.open authentication plus MAC
C.open authentication plus EAP
D.a shared key
您可能感興趣的試卷
你可能感興趣的試題
You have just finished aligning a Cisco Aironet 1400 Series Wireless Bridge link using installationmode.When you set the link back to operational mode you loose association to the root bridge.
Which action will correct the problem？（）
A.Configure the bridge to force infrastructure devices to associate only to the SSID parameter.
B.Enable passwords on both bridges.
C.Configure the distance parameter value.
D.Configure the proper channel.
You are troubleshooting a one-way call problem with a Cisco 7920 wireless IP phone on astandalone WLAN.
What may have caused this problem？（）
A.The minimum data rate is not set to 11 Mbps.
B.Publicly Secure Packet forwarding is enabled.
C.The access point is set to the least congested channel.
D.An address resolution protocol has been disabled.
On a Cisco Aironet 1130AG Series standalone access point， the status LED is dark blue andblinking.
What does this indicate？（）
A.The internal radio has failed.
B.A firmware upgrade is in progress.
C.An access point buffer overflow is occurring.
D.The access point is booting.
In a deployment using standalone access points， clients set up to authenticate with EAP-PEAP orEAP-Cisco Wireless （Cisco-LEAP） cannot authenticate. When you inspect the Failed Attemptsreport on the Cisco Secure ACS，you find this error："Unknown network access server NAS."
Which problemmayhave caused this failure？（）
A.misconfigured IP address of the AAA server on the access point
B.misconfigured EAP type on the access point
C.misconfigured IP address of the access point on the AAA server
D.misconfigured EAP type on the AAA server
A.router（config-ssid）# guest-mode
B.router（config-ssid）# advertise
C.router（config-ssid）# enable
D.router（config-ssid）# broadcast
最新試題
On a WLAN controller， what is the default roaming bandwidth percentage reserved for voice clients？（）
An REAP was supporting 16 WLANs， but now it only supports one.What happened to cause the change？（）
If it is properly deployed， a controller-based access point is capable of monitoring all VLANs on anetwork when you select which of the following modes from the AP Mode drop-down menu onthe controller？（）
A mobility group is created by a Cisco WLCM and 4402 Series Wireless LAN Controller. A client thatis anchored on the Cisco WLCM roams to an access point on the 4402 controller. You then run adebug command on the 4402 controller.Which message would best describe the establishment ofthe tunnel from the foreign controller’s perspective？（）
You have a very few Cisco 7920 wireless IP phones on your network， but lots of wireless laptops.You want to increase the bandwidth available for the laptops by decreasing the bandwidth reserved for the Cisco 7920 phones.What is the lowest percentage of voice-allocated bandwidthyou can select on the WLAN controller？（）
You want to dynamically assign users to an 802.1Q VLAN as a result of their authentication. Inorder to accomplish this.Which two IETF RADIUS attributes should you configure on the CiscoSecure ACS？ （）
How many WLANs can a Cisco Aironet 1242 in H-REAP mode support when actively connected toa wireless controller？（）
When configuring a WLAN controller for a voice application using Cisco 7920 wireless IP phones，which two general control settings should you select？（）
You have just finished aligning a Cisco Aironet 1400 Series Wireless Bridge link using installationmode. When you set the link back to operational mode you loose association to the root bridge.Which action will correct the problem？（）
The IOS of a North American Cisco Aironet 1130AG Series standalone access point has becomecorrupt. You must therefore reload the TFTP firmware.Before you press and hold the MODEbutton， you should verify that the file name is which of the following？（）