You are using ADU and are authenticated and associated to an access point. However， you are unable toobtain an IP address.
Which of these has caused this problem？（）
A.invalid SSID
B.invalid 802.1X authentication type
C.invalid encryption type
D.invalid WEP key
您可能感興趣的試卷
你可能感興趣的試題
Your customer has deployed a Cisco Wireless Location Appliance within its warehouse environment.However， employees there have been experiencing problems when tracking objects using active RFIDtags. You use an access point scan to determine if the Location Appliance has been deployed correctly.
Making which change to warehouse deployment location services will most likely correct the problem？（）
A.allow for the automatic containment of rogue access points
B.ensure each area is covered by a minimum of three access points
C.ensure channels are deployed such that they do not overlap
D.ensure a minimum RSSI value of -50
On a Cisco 1000 Series controller-based access point， the alarm LED is flashing red， but the other LEDsare off.
What is this access point indicating？（）
A.It has lost contact with the controller.
B.It requires a code upgrade.
C.It is operating normally.
D.Its IP address already exists.
On a standalone access point， client association using EAP-Cisco Wireless （Cisco-LEAP） is failing， butassociation using EAP-PEAP is functioning.
What needs to be enabled on the standalone access point tocorrect this issue？（）
A.a shared key
B.network EAP
C.open authentication plus EAP
D.open authentication plus MAC
A client roams from H-REAP AP1 to H-REAP AP2. The client is unable to associate to H-REAP AP2. H-REAP AP2 has six other clients associated to it， which continue to pass traffic.
What has caused this problem？（）
A.H-REAP AP1 lost its connection to the controller.
B.H-REAP AP2 lost its connection to the controller.
C.H-REAP AP1 has reached its client limit.
D.H-REAP AP2 has reached its client limit.
A Cisco Aironet 1020 controller-based access point has been connected to a Catalyst 3550-24 PWRSwitch. However， when it is powered up， the access point fails.
What has caused this problem？（）
A.access point has not been initialized with the primary controller
B.switch port is not enabled
C.switch does not support 802.3af
D.access point does not support 802.11h
E.incorrect switch power supply
最新試題
You have been called upon to add location-based services into an existing controller-basedwireless design which primarily encompasses handheld devices such as barcode scanners and Cisco7920 wireless IP phones.In which mode should you deploy the additional access points to achievethe density required without excessive co-channel interference？（）
When configuring a WLAN controller for a voice application using Cisco 7920 wireless IP phones，which two general control settings should you select？（）
You are configuring an RF group of controllers that coordinate Radio Resource Management calculations.What is the maximum number of WLAN controllers that you can add？（）
Static WEP is configured on the access point. You are authenticated and associated to the accesspoint but are unable to obtain an IP address.Which of the following will cause this problem？（）
An REAP was supporting 16 WLANs， but now it only supports one.What happened to cause the change？（）
You are trying to change the polling parameters used by the location manager via the Cisco WCS，and your request is being denied. What is wrong？（）
Which of the following parameter sets must be configured on the Cisco Wireless Location Appliance？（）
You are configuring a wireless LAN controller for QoS.Which 802.11e user priority tag should you apply to voice applications？（）
What is the maximum number of wireless controllers that the highest-end Cisco WCS server canmanage？（）
On a WLAN controller， what is the default roaming bandwidth percentage reserved for voice clients？（）