You have been called upon to add location-based services into an existing controller-based
wireless design which primarily encompasses handheld devices such as barcode scanners and Cisco7920 wireless IP phones.
In which mode should you deploy the additional access points to achievethe density required without excessive co-channel interference？（）
A.tracking mode
B.monitor mode
C.location mode
D.sniffer mode
您可能感興趣的試卷
你可能感興趣的試題
A Cisco Aironet 1020 controller-based access point has been connected to a Catalyst 3550-24 PWRSwitch. However， when it is powered up， the access point fails.
What has caused this problem？（）
A.access point does not support 802.11h
B.incorrect switch power supply
C.switch port is not enabled
D.switch does not support 802.3af
E.access point has not been initialized with the primary controller
A.Acceptance Test Plan
B.Change Management
C.Incident Management
D.Configuration Management
A.Ongoing Support Handoff Meeting
B.Staff Training
C.Detailed Design Development
D.Staging and System Migration
On a standalone access point， client association using EAP-Cisco Wireless （Cisco-LEAP） is failing，but association using EAP-PEAP is functioning.
What needs to be enabled on the standalone accesspoint to correct this issue？（）
A.network EAP
B.open authentication plus MAC
C.open authentication plus EAP
D.a shared key
You have just finished aligning a Cisco Aironet 1400 Series Wireless Bridge link using installationmode.When you set the link back to operational mode you loose association to the root bridge.
Which action will correct the problem？（）
A.Configure the bridge to force infrastructure devices to associate only to the SSID parameter.
B.Enable passwords on both bridges.
C.Configure the distance parameter value.
D.Configure the proper channel.
最新試題
The IOS of a North American Cisco Aironet 1130AG Series standalone access point has becomecorrupt. You must therefore reload the TFTP firmware.Before you press and hold the MODEbutton， you should verify that the file name is which of the following？（）
A Cisco WCS version 4.0 has been installed on a server with a dual Pentium 3.0 GHz processor，4GB RAM， and an 80 GB hard drive. A location appliance has been incorporated into the networkand is being monitored by the Cisco WCS. There are 3000 devices to be tracked but not all of themare being tracked on the Cisco WCS.What can be done to correct the problem？（）
You have just finished aligning a Cisco Aironet 1400 Series Wireless Bridge link using installationmode. When you set the link back to operational mode you loose association to the root bridge.Which action will correct the problem？（）
A client roams from H-REAP AP1 to H-REAP AP2. The client is unable to associate to H-REAP AP2.H-REAP AP2 has six other clients associated to it， which continue to pass traffic.What has causedthis problem？（）
When configuring Cisco Secure ACS to support wireless EAP authentication， which device must be configured as a AAA client？（）
You are charges with implementing a secure wireless installation which will provide Internet accessto client devices but will not allow communications between wireless clients.In addition to implementing PSPF or peer-to-peer blocking on the wireless side，which of the following actionsshould you perform on the wired infrastructure？（）
The Cisco Wireless Location Appliance provides an audit trail for each device tracked for up to how many days？（）
What is the maximum number of wireless controllers that the highest-end Cisco WCS server canmanage？（）
Clients using Cisco-LEAP and EAP-FAST authentication are having no problems logging on to thewireless network， but clients using PEAP are failing to log on.Which situation would result in thistype of problem？（）
You are installing a Cisco 4402 Series Wireless LAN Controller.What type of interface is used on the uplink port？（）