A.Visually verify the MAC addresses and then telnet to the switches to enter the switchport-port security mac-address command.
B.Have end users e-mail their MAC addresses. Telnet to the switch to enter the switchport-port security mac-address command.
C.Use the switchport port-security MAC address sticky command on all the switch ports that have end devices connected to them.
D.Use show mac-address-table to determine the addresses that are associated with each port and then enter the commands on each switch for MAC address port-security.
您可能感興趣的試卷
你可能感興趣的試題
A.Administratively shut down the interfaces.
B.Physically secure the interfaces.
C.Configure a virtual terminal password and login process.
D.Enter an access list and applyit to the terminal interfaces using theaccess-class command.
E.Create an access list and applyit to the terminal interfaces using theaccess-group command.
A.Configure the switch to be in VTP client mode.
B.Configure the switch to be in VTP domaint mode.
C.Configure the switch to be in VTP transparent mode.
D.Configure the switch to be in VTPv2
A.show interfaces interface
B.show interfaces interface trunk
C.show interfaces interface switchport
D.show ip interface brief
E.show interfaces vlan
A.Telnet to WANRouter and execute the command show interfaces S0/0
B.Telnet to WANRouter and execute the command show processes S0/0
C.Telnet to WANRouter and execute the command show running-configuration
D.Telnet to WANRouter and execute the command show controller S0/0
E.Physically examine the cable between WANRouter S0/0 and the DCE
F.Establish a console session on WANRouter and execute the command show interfaces S0/0
Refer to the topology shown in the exhibit. Which ports will be STP designated ports if all the links are operating at the same bandwidth? （）
A.Switch A - Fa0/0
B.Switch A - Fa0/1
C.Switch B - Fa0/0
D.Switch B - Fa0/1
E.Switch C - Fa0/0
F.Switch C - Fa0/1
最新試題
請參見圖示。哪種邏輯拓?fù)涫菍?duì)圖示網絡的準確描述？（）
請參見圖示。一臺主機正使用NAT 連接到Internet。下列哪三項IP 地址可實現此連接？（）
請參見圖示。當計算機A 向計算機D 發送幀時，哪些計算機會接收該幀？（）
何時必須使用clock rate 命令配置路由器串行接口？（）
請參見圖示。圖中所示路由表所屬的PC 已正確配置。IP 地址192.168.1.254屬于哪一個網絡設備或接口？（）
請參見圖示。某用戶想要查看當前的配置。圖中所示為ipconfig/all 命令的輸出。從此輸出可以得到哪三項結論？（）
請參見圖示。電纜1和電纜2分別按照特定的物理層要求接線。哪三個網段使用電纜2？（）
請參見圖示。網絡技術人員使用圖中所示的連接將主機A 連接到路由器以創建初始配置。下列有關此連接的陳述中哪一項正確？（）
要將數據包發送到遠程網絡，應使用哪種設備？（）
請參見圖示。RouterB 已經過正確配置。RouterA 的以太網接口Fa0/0已使用如圖所示的命令進行配置。但是，從RouterA 的Fa0/0接口無法成功ping 通RouterB 的Fa0/0接口。應在RouterA 上采取什么措施來解決此問題？（）