A.point-to-point and multiaccess
B.point-to-multipoint and multiaccess
C.point-to-point and point-to-multipoint
D.nonbroadcast and broadcast multipoint
E.nonbroadcast and broadcast multiaccess
您可能感興趣的試卷
你可能感興趣的試題
A.to prevent unauthorized Telnet access to a switch port
B.to limit the number of Layer 2 broadcasts on a particular switch port
C.to prevent unauthorized hosts from accessing the LAN
D.to protect the IP and MAC address of the switch and associated ports
E.to block unauthorized access to the switch management interfaces over common TCP ports
A.permit all packets matching the first three octets of the source address to all destinations
B.permit all packets matching the last octet of the destination address and accept all source addresses
C.permit all packets from the third subnet of the network address to all destinations
D.permit all packets matching the host bits in the source address to all destinations
E.permit all packets to destinations matching the first three octets in the destination address
A.Establish a direct link from the switch to all other switches in the network.
B.Assign the switch a higher MAC address than the other switches in the network have.
C.Configure the switch so that it has a lower priority than other switches in the network.
D.Configure the switch for full-duplex operation and configure the other switches for half-duplex operation.
E.Connect the switch directly to the MDF router， which will force the switch to assume the role of root bridge.
A.It is used to validate the sources of VTP advertisements sent between switches.
B.It is used to access the VTP server to make changes to the VTP configuration.
C.It allows two VTP servers to exist in the same domain， each configured with different passwords.
D.It is the password required when promoting a switch from VTP client mode to VTP server mode.
E.It is used to prevent a switch newly added to the network from sending incorrect VLAN information to the other switches in the domain.
A.to verify the type of cable interconnecting two devices
B.to determine the status of network services on a remote device
C.to obtain VLAN information from directly connected switches
D.to verify Layer 2 connectivity between two devices when Layer 3 fails
E.to obtain the IP address of a connected device in order to telnet to the device
F.to determine the status of the routing protocols between directly connected routers
最新試題
If all OSPF routers in a single area are configured with the same priority value,what value dose a router use for the ODPF router ID in the absence of a loopback interface?（）
What is the subnetwork address for a host with the IP address 201.100.5.68/28?（）
An administrator must assign static IP addresses to the servers in a network.For network 192.168.20.24/29, the router is assigned the first usable host address while the sales server is given the last usable host address. Which of the following should be entered into the IP propertied box for the sales server?（）
While troubleshooting a network problem,a technician discovers that the current copy of the Cisco IOS is outdated and needs to be updated.Which of the following commands would the technician issue to replace the Cisco router IOS with the newer version?（）
Three switches are connected to one anther via trunk ports.Assuming the default switch configuration,which switch is elected as the root bridge for the spanning-tree instance of vlan 1?（）
Three access ports have been installed and configured to a small office.What term defines the wireless topology?（）
The network administrator cannot to switch 1 over a telnet session,although the hosts attached to switch 1 can ping the interface Fa0/0 of the router.Given the information in the graphic and assuming that the router and switch2 are configured properly,which of the following commands should be issued on switch 1 to correct this problem?（）
Which pairing reflects a correct protocol-and-metric relationship?（）
An employee of ABC company has move to an office on a different floor. Although the administrator is able to telnet to all of the routers,the address of Switch F is needed in order to verify that the employee remains in the same VLAN.Which action could be used by the administrator to find the IP address of Switch F?（）
Which command is used to display the collection of OSPF link states?（）