You need to configure a new Company switch to support DTP.
Which DTP switchport mode parameter sets the switch port to actively send and respond to DTP negotiation frames？ （）
A. Access
B. No negotiate
C. Trunk
D. Dynamic desirable
E. Dynamic auto
F. None of the other alternatives apply
您可能感興趣的試卷
你可能感興趣的試題
While using a packet analyzer， you notice four additional bytes being added to the packets in the Company network.
Which protocol inserts a four byte tag into the Ethernet frame and recalculates CRC value？ （）
A. DTP
B. VTP
C. 802.1Q
D. ISL
E. None of the other alternatives apply
You need to configure a new Company switch for trunking.
Which switch command enables a trunking protocol that appends a four byte CRC to the packet？（）
A. CompanySwitch（config-if）#switchport trunk encapsulation dot1q
B. CompanySwitch（config-if）#switchport trunk encapsulation itef
C. CompanySwitch（config-if）#switchport trunk encapsulation fddi
D. CompanySwitch（config-if）#switchport trunk encapsulation isl
E. None of the other alternatives apply
Switch R1 has been configured with DTP using the desirable option.
Which statement describes Dynamic Trunking Protocol （DTP） desirable mode？（）
A. The interface actively attempts to convert the link to a trunk link.
B. The interface is put into permanent trunking mode but prevented from generating DTP frames.
C. The interface is put into permanent trunking mode and negotiates to convert the link into a trunk link.
D. The interface is put into a passive mode， waiting to convert the link to a trunk link.
E. None of the other alternatives apply
The core Company switches are configured to use 802.1Q trunks.
Which three statements are correct with regard to the IEEE 802.1Q standard？（）
A. The IEEE 802.1Q frame format adds a 4 byte field to a Ethernet frame
B. The packet is encapsulated with a 26 byte header and a 4 byte FCS
C. The protocol uses point-to-multipoint connectivity
D. The protocol uses point-to-point connectivity
E. The IEEE 802.1Q frame uses multicast destination of 0x01-00-0c-00-00
F. The IEEE 802.1Q frame retains the original MAC destination address
Refer to the exhibit. On the basis of the output generated by the show commands，
which two statements are true？（）
A. Because it is configured as a trunk interface， interface gigabitethernet 0/1 does not appear in the show vlan output.
B. VLAN 1 will not be encapsulated with an 802.1q header.
C. There are no native VLANs configured on the trunk.
D. VLAN 2 will not be encapsulated with an 802.1q header.
E. All interfaces on the switch have been configured as access ports.
F. Because it has not been assigned to any VLAN， interface gigabitethernet 0/1 does not appear in the show vlan output.
最新試題
Refer to the exhibit. The command switchport mode access is issued on interface FastEthernet0/13 on switch CAT1. What will be the result？（）
Which option correctly identifies the Cisco IOS switching methods in descending order from the fastest method to the slowest method？（）
Which two statements are true about BPDU port-guard and BPDU filtering？（）
Which two statements are true when the extended system ID feature is enabled？ （）
Which three statements are true of the Link Aggregation Control Protocol （LACP）？（）
Refer to the exhibit. What does the command channel-group 1 mode desirable do？ （）
Refer to the exhibit. Switch 15 is configured as the root switch for VLAN 10 but not for VLAN 20. If the STP configuration is correct， what will be true about Switch 15？（）
Refer to the exhibit. What command was issued on the Layer 3 switch Sw1 between Exhibit #1 and Exhibit #2？（）
Refer to the exhibit and the partial configuration of switch SW_A and SW_B. STP is configured on all switches in the network. SW_B receives this error message on the console port：00：06：34： %CDP-4-DUPLEX_MISMATCH： duplex mismatch discovered on FastEthernet0/5 （not half duplex）， with SW_A FastEthernet0/4 （half duplex） ， with TBA05071417（Cat6K-B） 0/4 （half duplex）. What would be the possible outcome of the problem？（）
Refer to the exhibit. Which statement is true about the output？（）