The Company security administrator is concerned with VLAN hopping based attacks.
Which two statements about these attacks are true？ （）
A. Attacks are prevented by utilizing the port-security feature.
B. An end station attempts to gain access to all VLANs by transmitting Ethernet frames in the 802.1q encapsulation.
C. Configuring an interface with the switchport mode dynamic command will prevent VLAN hopping.
D. An end station attempts to redirect VLAN traffic by transmitting Ethernet frames in the 802.1q encapsulation.
E. Configuring an interface with the "switchport mode access" command will prevent VLAN hopping.
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit. PCs in VLAN 2 are not able to communicate with PCs in VLAN 3.
What could be the cause？（）
A. IP routing is not enabled.
B. VTP is not configured correctly on the interfaces.
C. The command mls rp management-interface is missing.
D. The command mls rp ip must be disabled to enable the routing.
You are configuring a Cisco multilayer switch for the Company network.
Which command would you use to configure a port to act as a routed interface？（）
A. ip routing
B. switchport mode trunk
C. no switchport
D. switchport trunk native vlan 1
E. None of the other alternatives apply
Which of the following could be used to provide a Layer 3 data path between separate VLANs？（）
A. VLAN trunking
B. An external router
C. An internal route processor
D. VLAN capable bridge
E. EtherChannel
Inter-VLAN routing has been implemented in the Company network. In VLAN routing，
what are some of the disadvantages of designing a router-on-stick configuration？ （）
A. InterVLAN routing cannot be filtered by the router.
B. The router becomes a single point of failure for the network.
C. Routers will not route STP BPDUs.
D. There is a possibility of inadequate bandwidth for each VLAN.
E. Additional overhead on the router can occur.
F. NetFlow Switching is required for InterVLAN accounting.
The Company network needs to pass traffic between VLANs.
Which device should be used to accomplish this？ （）
A. Hub
B. Switch
C. Router
D. Bridge
E. None of the other alternatives apply
最新試題
Refer to the exhibit. LACP has been configured on Switch1 as shown. Which is the correct command set to configure LACP on Switch2？（）
Refer to the exhibit. STP has been implemented in the network. Switch SW_A is the root switch for the default VLAN. To reduce the broadcast domain， the network administrator decides to split users on the network into VLAN 2 and VLAN 10. The administrator issues the command spanning-tree vlan 2 root primary on switch SW_A. What will happen as a result of this change？（）
Refer to the exhibit and the partial configuration of switch SW_A and SW_B. STP is configured on all switches in the network. SW_B receives this error message on the console port：00：06：34： %CDP-4-DUPLEX_MISMATCH： duplex mismatch discovered on FastEthernet0/5 （not half duplex）， with SW_A FastEthernet0/4 （half duplex） ， with TBA05071417（Cat6K-B） 0/4 （half duplex）. What would be the possible outcome of the problem？（）
What is the configured priority value of the Vlan105’s group on DS2 ？（）
If G1/0/1 on DS1 is shutdown， what will be the current priority value of the Vlan105’s group on DS1 ？（）
What will occur when a nonedge switch port that is configured for Rapid Spanning Tree does not receive a BPDU from its neighbor for three consecutive hello time intervals？（）
During routine maintenance， G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However， after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ？ （）
Refer to the exhibit. All network links are FastEthernet. Although there is complete connectivity throughout the network， Front Line users have been complaining that they experience slower network performance when accessing the server farm than the Reception office experiences. Based on the exhibit， which two statements are true？（）
Refer to the exhibit. Based on the output of the show spanning-tree command， which statement is true？ （）
Refer to the exhibit. Switch S2 contains the default configuration. Switches S1 and S3 both have had the command spanning-tree mode rapid-pvst issued on them. What will be the result？（）