Refer to the exhibit.
What will happen to traffic within VLAN 14 with a source address of 172.16.10.5？ （）
A. The traffic will be forwarded to the router processor for further processing.
B. The traffic will be dropped.
C. The traffic will be forwarded to the TCAM for further processing.
D. The traffic will be forwarded without further processing.
您可能感興趣的試卷
你可能感興趣的試題
A hacker on the Company network is attempting to hop onto a different VLAN.
Which two statements about VLAN hopping are true？ （）
A. An end station attempts to gain access to all VLANs by transmitting Ethernet frames in the 802.1q encapsulation.
B. Configuring an interface with the "switchport mode dynamic" command will prevent VLAN hopping.
C. Attacks are prevented by utilizing the port-security feature.
D. Configuring an interface with the "switchport mode access" command will prevent VLAN hopping.
E. An end station attempts to redirect VLAN traffic by broadcasting multiple ARP requests.
The Company security administrator wants to prevent VLAN hopping on the network.
What is one method that can be used to do this？ （）
A. Attacks are prevented by utilizing the port-security feature.
B. An end station attempts to gain access to all VLANs by transmitting Ethernet frames in the 802.1q encapsulation.
C. Configuring an interface with the switchport mode dynamic command will prevent VLAN hopping.
D. An end station attempts to redirect VLAN traffic by transmitting Ethernet frames in the 802.1q encapsulation.
E. Configuring an interface with the "switchport mode access" command will prevent VLAN hopping.
The Company security administrator is concerned with VLAN hopping based attacks.
Which two statements about these attacks are true？ （）
A. Attacks are prevented by utilizing the port-security feature.
B. An end station attempts to gain access to all VLANs by transmitting Ethernet frames in the 802.1q encapsulation.
C. Configuring an interface with the switchport mode dynamic command will prevent VLAN hopping.
D. An end station attempts to redirect VLAN traffic by transmitting Ethernet frames in the 802.1q encapsulation.
E. Configuring an interface with the "switchport mode access" command will prevent VLAN hopping.
Refer to the exhibit. PCs in VLAN 2 are not able to communicate with PCs in VLAN 3.
What could be the cause？（）
A. IP routing is not enabled.
B. VTP is not configured correctly on the interfaces.
C. The command mls rp management-interface is missing.
D. The command mls rp ip must be disabled to enable the routing.
You are configuring a Cisco multilayer switch for the Company network.
Which command would you use to configure a port to act as a routed interface？（）
A. ip routing
B. switchport mode trunk
C. no switchport
D. switchport trunk native vlan 1
E. None of the other alternatives apply
最新試題
Which two statements are true about BPDU port-guard and BPDU filtering？（）
Which three statements are true of the Link Aggregation Control Protocol （LACP）？（）
Examine the diagram. A network administrator has recently installed the above switched network using 3550s and would like to control the selection of the root bridge.Which switch should theadministrator configure as the root bridge and which configuration command must theadministrator enter to accomplish this？（）
Which option correctly identifies the Cisco IOS switching methods in descending order from the fastest method to the slowest method？（）
Refer to the exhibit. Which statement is true about the output？（）
What two things will occur when an edge port receives a BPDU？（）
Which router redundancy protocol cannot be configured for interface tracking？（）
Which statement is correct about RSTP port roles？（）
Refer to the exhibit. What does the command channel-group 1 mode desirable do？ （）
During routine maintenance， G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However， after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ？ （）