You administer the network shown above. You issue the show interfaces trunk command on SwitchA and receive the following output：
SwitchA#show interfaces trunk
Port Mode Encapsulation Status Native vlan
Fa0/1 desirable -n802.1q trunking 1
Port Vlans allowed on trunk Fa0/1 1-4094
Port Vlans allowed and active in management domain
Fa0/1 1-9，31-37
Port Vlans in spanning tree forwarding state and not pruned
Fa0/1 1-9，31，33-37
Which of the following statements is true regarding VLAN 32？（）
A. VLAN 32 is not allowed on the trunk port.
B. VLAN 32 is not active on the switch.
C. Traffic from VLAN 32 is not being sent over the trunk port.
D. Traffic from VLAN 32 is not restricted to only the trunk ports that require it.
您可能感興趣的試卷
你可能感興趣的試題
You want to configure a switched internetwork with multiple VLANs as shown above.
Which of the following commands should you issue on SwitchA for the port connected to SwitchB？ （）
A. switchport mode trunk
B. switchport access vlan 5
C. switchport mode access vlan 5
D. switchport trunk native vlan 5
Refer to the exhibit.
Which of the following should you do to configure the IP phone to override the priority of the data packets it receives from the host？ （）
A. Issue the mls qos trust cos command on the switch port connected to the IP phone.
B. Issue the switchport priority extend cos command on the switch port connected to the IP phone.
C. Issue the switchport priority extend cos command on the IP phone.
D. Issue the mls qos trust cos command on the IP phone.
You administer a network that uses two routers， R1 and R2， configured as an HSRP group to provide redundancy for the gateway. Router R1 is the active router and has been configured as follows：
R1#configure terminal
R1（config）#interface fa0/0
R1（config-if）#ip address 10.10.0.5 255.255.255.0
R1（config-if）#standby 1 priority 150
R1（config-if）#standby preempt delay minimum 50
R1（config-if）#standby 1 track interface fa0/2 15
R1（config-if）#standby 1 ip 10.10.0.20
Which of the following describes the effect the standby preempt delay minimum 50 command will have on router R1？（）
A. The HSRP priority for router R1 will increase to 200.
B. Router R1 will become the standby router if the priority drops below 50.
C. The HSRP priority for router R1 will decrease to 50 points when Fa0/2 goes down.
D. Router R1 will wait 50 seconds before attempting to preempt the active router.
Routers R1 and R2 are configured for HSRP as shown below：
Router R1：
interface ethernet 0
ip address 20.6.2.1 255.255.255.0
standby 35 ip 20.6.2.21
standby 35 priority 100
interface ethernet 1
ip address 20.6.1.1.2 255.255.255.0
standby 34 ip 20.6.1.21
Router R2：
interface ethernet 0
ip address 20.6.2.2 255.255.255.0
standby 35 ip 20.6.2.21
interface ethernet 1
ip address 20.6.1.1.1 255.255.255.0
standby 34 ip 20.6.1.21
standby 34 priority 100
You have configured the routers R1 & R2 with HSRP. While debugging router R2 you notice very
frequent HSRP group state transitions.
What is the most likely cause of this？ （）
A. physical layer issues
B. no spanning tree loops
C. use of non-default HSRP timers
D. failure to set the command standby 35 preempt
Exhibit
Which command will ensure that Company2 will be the primary router for traffic using the gateway address of 172.16.15.20？ （）
A. On R2 add the command standby 1 priority 80
B. On R1 add the command standby 1 priority 110
C. On R1 add the command standby 1 priority 80
D. On R2 remove the command standby 1 preempt
最新試題
Refer to the exhibit. On the basis of the output of the show spanning-tree inconsistentports command， which statement about interfaces FastEthernet 0/1 and FastEthernet 0/2 is true？（）
What two things will occur when an edge port receives a BPDU？（）
Which three statements are true of the Link Aggregation Control Protocol （LACP）？（）
During routine maintenance， G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However， after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ？ （）
Based on the show spanning-tree vlan 200 output shown in the exhibit， which two statements about the STP process for VLAN 200 are true？ （）
Refer to the exhibit. Switch 15 is configured as the root switch for VLAN 10 but not for VLAN 20. If the STP configuration is correct， what will be true about Switch 15？（）
Which two statements are true when the extended system ID feature is enabled？ （）
How are STP timers and state transitions affected when a topology change occurs in an STP environment？（）
Which statement is correct about RSTP port roles？（）
Which two statements about the various implementations of STP are true？（）