Refer to the exhibit. Based upon the configuration, you need to understand why the policy routi match counts are not increasing. Which would be the first logical step to take?（）
A. Confirm if there are other problematic route - map statements that precede divert.
B. Check the access list for log hits.
C. Check the routing table for 212.50.185.126.
D. Remove any two of the set clauses. (Multiple set clause entries will cause PBR to use the routing table.)
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit. How would you confirm on R1 that load balancing is actually occurring on the default - netw ork (0.0.0.0)?（）
A. Use ping and the show ip route command to confirm the timers for each default network resets to 0.
B. Load balancing does not occur over default networks; the second route will only be used for failover.
C. Use an extended ping al ong with repeated show ip route commands to confirm the gateway of last resort address toggles back and forth.
D. Use the traceroute command to an address that is not explicitly in the routing table.
Refer to the exhibit. R1 accesses the Internet using E0/0. You have been asked to co nfigure R1 so that a default route is generated to its downstream devices (191.0.0.1 and 192.0.0.1). Which commands would create this configuration? （）
A.router eigrp 190 redistribute static ! ip route 0.0.0.0 0.0.0.0 Null0
B.ip default - network 2 0.0.0.0
C.router eigrp 190 redistribute static ! ip route 0.0.0.0 255.255.255.255 Null0
D.ip default - network 20.20.20.0
Refer to the exhibit. You want to use all the routes in the EIGRP topology for IP load balancing. Which two EIGRP subcommands wou ld you use to accomplish this goal?（）
A. traffic - share balanced
B. distance
C. maximum- paths
D. default - network
E. variance
A. performing inter - VLAN routing
B. performing 802.1Q trunking
C. performi ng ISL trunking
D. Ethernet Switch Module installed
E. ADSL WIC installed
F. running Call Manager Express
A. PPPoE
B. DOCSIS
C. CMTS
D. AAL5
最新試題
Look at the following configuration below and select the statements that are true.（）RD2(config)#router ospf 100RD2(config - router)# distance 180 10.1.10.1 0.0.0.0 match - meRD2(config -router)#!RD2(config - router) #ip access - list standard match - meRD2(config - std - nacl)# permit host 172.16.0.0
The answers each list a tunnel method and two consecutive IPv6 address quartets.Which answers identify a tunneling method that relies on an IPv4 address to be embedded into an IPv6 address, within the correct quartets listed?（）
Which of the following is the shortest valid abbreviation for FE80:0000:0000:0000:0010:0000:0000:0123?（）
Router R1 has been conf igured with an ipv6 route 2000::/64 S0/0/0 64 command.Which of the following does the 64 at the end of the command represent?（）
Router R1 has two LAN interfaces and three serial interfaces enabled for IPv6. All the inte rfaces use link local addresses automatically generated by the router.Which of the following could be the link local address of R1's interface S0/0?（）
Which of the following answers lists either a protocol or function that can be used by a host to dynamically learn its own IPv6 address?（）
Router R1 lists the following output from a show command. Which of the following is true about R1?（）R1# show ip v6 interface f0/0FastEthernet0/0 is up, line protocol is upIPv6 is enabled, link - local address is FE80::213:19FF:FE12:3456No Virtual link - local address(es):Global unicast address(es):2000::4:213:19FF:FE12:3456, subnet is 2000:0:0:4::/64 [EUI]Jo ined group address(es):FF02::1FF02::2FF02::1:FF:12:3456
Which of the following answers lists a multicast IPv6 address?（）
Which of the following features work the same in both RIP- 2 and RIPng?（）
Router R1, a branch router, connects to the Internet using DSL. The engineer plans to use a configuration with a dialer interface. The answers list a feature and interface on which the feature could be configured.Which combinations accurately describe the interface under which a feature will be configured?（）