A Cisco WCS version 4.0 has been installed on a server with a dual Pentium 3.0 GHz processor， 4 GBRAM， and an 80 GB hard drive. A location appliance has been incorporated into the network and is beingmonitored by the Cisco WCS. There are 3000 devices to be tracked but not all of them are being trackedon the Cisco WCS.
What can be done to correct the problem？（）
A.Add 4 GB of RAM to the Cisco WCS.
B.Add a 120 GB hard drive to the Cisco WCS.
C.Add a new location appliance.
D.Add a new Cisco WCS server dedicated to the location appliance.
您可能感興趣的試卷
你可能感興趣的試題
You are troubleshooting a problem with a Cisco 7920 wireless IP phone on a standalone WLAN. The phonerings but， when you answer， the call is dropped.
What may have caused this problem？（）
A.The minimum data rate is not set to 11 Mbps.
B.An address resolution protocol is enabled.
C.Publicly Secure Packet forwarding is enabled.
D.The access point is set to the least congested channel.
You are troubleshooting a one-way call problem with a Cisco 7920 wireless IP phone on a standaloneWLAN.
What may have caused this problem？（）
A.The minimum data rate is not set to 11 Mbps.
B.An address resolution protocol has been disabled.
C.Publicly Secure Packet forwarding is enabled.
D.The access point is set to the least congested channel.
You are troubleshooting a problem with a Cisco 7920 wireless IP phone that is causing the
phone to drop calls. The problem appears to be a roaming bandwidth issue. In order to verify what kind ofissue it is， you decide to increase the bandwidth reserved for roaming on the WLAN controller to themaximum.
What level do you set the bandwidth to？（）
A.5 percent
B.15 percent
C.25 percent
D.35 percent
You have very few Cisco 7920 wireless IP phones on your network， but lots of wireless laptops. You want toincrease the bandwidth available for the laptops by decreasing the bandwidth reserved for the Cisco 7920phones.
What is the lowest percentage of voice-allocated bandwidth you can select on the WLANcontroller？（）
A.25 percent
B.40 percent
C.55 percent
D.75 percent
最新試題
The IOS of a North American Cisco Aironet 1130AG Series standalone access point has becomecorrupt. You must therefore reload the TFTP firmware.Before you press and hold the MODEbutton， you should verify that the file name is which of the following？（）
Clients using Cisco-LEAP and EAP-FAST authentication are having no problems logging on to thewireless network， but clients using PEAP are failing to log on.Which situation would result in thistype of problem？（）
You are charges with implementing a secure wireless installation which will provide Internet accessto client devices but will not allow communications between wireless clients.In addition to implementing PSPF or peer-to-peer blocking on the wireless side，which of the following actionsshould you perform on the wired infrastructure？（）
You are installing a Cisco Aironet 1000 Series controller-based access point. When you boot it， allthe LEDs on the access point blink together.What does this indicate about the access point？（）
You want to dynamically assign users to an 802.1Q VLAN as a result of their authentication. Inorder to accomplish this.Which two IETF RADIUS attributes should you configure on the CiscoSecure ACS？ （）
How many WLANs can a Cisco Aironet 1242 in H-REAP mode support when actively connected toa wireless controller？（）
You have been called upon to add location-based services into an existing controller-basedwireless design which primarily encompasses handheld devices such as barcode scanners and Cisco7920 wireless IP phones.In which mode should you deploy the additional access points to achievethe density required without excessive co-channel interference？（）
On a Cisco Aironet 1240AG Series standalone access point， the radio LED is dark blue and blinking，but the status LED and Ethernet LED are both off.What does this indicate？（）
When configuring Cisco Secure ACS to support wireless EAP authentication， which device must be configured as a AAA client？（）
You are installing a Cisco 4402 Series Wireless LAN Controller.What type of interface is used on the uplink port？（）