A lightweight access point has been connected to a Catalyst 3550 24-PWR switch， and on power-up the access point fails.
What is the problem with the switch？（）
A.The power supply has inadequate wattage.
B.Power is incorrectly configured on the port.
C.It does not support 802.3af Poe.
D.Power is not enabled on the port.
您可能感興趣的試卷
你可能感興趣的試題
Two access points running the core feature set are connected to the same switch and are providingguest services.
If PSPF is enabled， what must be enabled on the switch to prevent clients fromseeing one another’s data？（）
A.port-based RADIUS
B.802.1q trunking
C.inline power
D.protected port
A.startup
B.site survey mode
C.lost connection to the controller
D.duplicate IP address
Last December you erected a bridge link between two buildings on your campus. It is now Apriland the foliage in the trees is full， and the bridge link will no longer maintain connectivity.
Which action will most likely solve the problem？（）
A.Change the channel selection.
B.Install higher gain antennas.
C.Raise the antennas.
D.Increase transmitter power.
An 802.1X client cannot authenticate to an autonomous access point configured for multiple
VLANs. The native VLAN does not have an SSID configured.
Which one of the following links being down would prevent the clients from authenticating？（）
A.between the RADIUS and the access point
B.between the client’s VLAN and the WLSE
C.between the native VLAN and the WLSE
D.between the client’s VLAN and the RADIUS
In a deployment using the lightweight access points， clients set up to authenticate with EAP-PEAPor EAP-Cisco Wireless （LEAP） cannot authenticate. Upon inspection of the Failed Attempts reportyou see the following error： "Unknown network access server NAS."
What two problems can causethis type of failure？（）
A.misconfigured IP address of the AAA server on the wireless controller
B.misconfigured IP address of the wireless LAN controller on the AAA server
C.misconfigured EAP type on the wireless LAN controller
D.misconfigured shared secret on the wireless LAN controller
E.misconfigured EAP type on the AAA server
最新試題
You are installing a Cisco Aironet 1000 Series controller-based access point. When you boot it， allthe LEDs on the access point blink together.What does this indicate about the access point？（）
An REAP was supporting 16 WLANs， but now it only supports one.What happened to cause the change？（）
Static WEP is configured on the access point. You are authenticated and associated to the accesspoint but are unable to obtain an IP address.Which of the following will cause this problem？（）
A mobility group is created by a Cisco WLCM and 4402 Series Wireless LAN Controller. A client thatis anchored on the Cisco WLCM roams to an access point on the 4402 controller. You then run adebug command on the 4402 controller.Which message would best describe the establishment ofthe tunnel from the foreign controller’s perspective？（）
A Cisco Wireless Location Appliance has been added to track RFID tags placed on laptops beingused in a school.Classrooms at the school have concrete block walls. During testing，you discoverthat the accuracy of the system needs to be improved.You decide to edit the map in the Cisco WCS to add the interior walls.How many interior walls can you add to improve the accuracy of thelocation appliance？（）
How many WLANs can a Cisco Aironet 1242 in H-REAP mode support when actively connected toa wireless controller？（）
You want to dynamically assign users to an 802.1Q VLAN as a result of their authentication. Inorder to accomplish this.Which two IETF RADIUS attributes should you configure on the CiscoSecure ACS？ （）
You are charges with implementing a secure wireless installation which will provide Internet accessto client devices but will not allow communications between wireless clients.In addition to implementing PSPF or peer-to-peer blocking on the wireless side，which of the following actionsshould you perform on the wired infrastructure？（）
Which of the following parameter sets must be configured on the Cisco Wireless Location Appliance？（）
You are troubleshooting a problem with a Cisco 7920 wireless IP phone that is causing the phoneto drop calls. The problem appears to be roaming bandwidth issue. In order to verify what kind ofissue it is， you decide to increase the bandwidth reserve for roaming on the WLAN controller tomaximum.What level do you set the bandwidth to？（）